DIODE 210S6ES63 No.12 DO-5 2 1 6-37 6-37 Repair or replace (After clean) Repair or replace (After clean) 余 Before disconnecting the connector, always turn the starting switch OFF. 余 Before carrying out below procedure, check all the related connectors are properly inserted and the fuse No.5,12 and 15 is not blown out. 余 After checking, insert the disconnected connectors again immediately unless otherwise specified. Replace Replace Replace 14.
WHEN STARTING SWITCH IS TURNED ON, WIPER MOTOR DOES NOT OPERATE CN-141 (7)- Fuse, CN-21 (4)-Fuse 1) Recheck fuse No.12 2) Disconnection CN-141(6)-Fuse Disconnection in wiring harness or poor contact Defective wiper motor Defective wiper motor controller YES Starting switch : ON Vottage : 20~30V NO NO 刕 YES Check voltage between CN-116 (6) and chassis Check voltage CN-141 (6)-and chassis Starting switch : ON Voltage : 20~30V 刔 NO YES NO YES NO YES Check operation of switch panel LED ON. Starting switch : ON Push wiper switch button Check operation of wiper motor and controller check voltage CN-141 (7) and chassis, CN-21 (4) and chassis Starting switch : OFF Voltage :
20~30V Check wiper motor resistance between CN-21 (2)-CN-21 (6) Resistance : 3~4 凂 YES NO NO YES NO YES Check valtage between CN-141 (11) and chassis Front sliding door-close Voltage : 0~1V Check voltage between CN-116 (4) and chassis Check voltage CN-116 (12) and chassis Check voltage CN-116 (15) and chassis Check continuity between CN-141 (2)-CN-116 (4), CN-141 (9)-CN-116 (12), CN-141 (10)-CN-116 (15), CN-141 (5)-Chassis , CN-141 (1)-CN-21 (5), CN-141 (3)-CN-21 (6), CN-141 (4)-CN-21 (2), CN-141 (13)-CN-21 (3) Sarting switch : ON Voltage :
0~1V NO YES Intermittent Washing Check operation wiper cut switch Front sliding door open-close 刕# 刔 NO YES Check operation wiper cut switch ront sliding door Check valtage pen-close between CN-141 YES YES (11) and chassis Check voltage NO Front sliding door-close between CN-116 Voltage : 0~1V (6) and chassis Check operation of switch panel Starting switch : ON NO NO LED ON. Vottage : 20~30V Starting switch : ON 刔 Push wiper switch button YES Check voltage between NO CN-116 (4) and chassis Intermittent NO Check voltage CN-116 刔 (12) and chassis Washing Check operation of wiper motor Check voltage CN-116 and controller (15) and chassis check voltage Sarting switch :
ON YESCN-141 (7) and Voltage : 0~1V chassis, CN-21 (4) and chassis NO Starting switch : OFF Voltage : 20~30V Check voltage CN-141 (6)-and YES chassis Check continuity Starting switch : ON YES Voltage : 20~30V between NO CN-141 (2)-CN-116 (4), CN-141 (9)-CN-116 (12), CN-141 (10)-CN-116 (15), 刕# CN-141 (5)-Chassis , NO Check wiper CN-141 (1)-CN-21 (5), motor resistance CN-141 (3)-CN-21 (6), between CN-21 CN-141 (4)-CN-21 (2), YES (2)-CN-21 (6) CN-141 (13)-CN-21 (3) YES Resistance :
3~4凂 Cause Remedy Defective wiper cut switch Disconnection in wiring harness or poor contact between CN-141 (11)- CS-53 Defective switch panel 1) Recheck fuse No.12 2) Disconnection in wiring harness or poor contact between CN-116 (6)- Fuse between CN-116 (13)-Chassis Defective switch panel 1) R echeck fuse No.5 2) D isconnection in wiring harness or poor contact between CN-141 (7)- Fuse, CN-21 (4)-Fuse 1) R echeck fuse No.12 2) D isconnection CN-141(6)-Fuse 刕 Disconnection in wiring harness or poor contact Defective wiper motor Defective wiper motor controller Replace Repair or replace (After clean) Replace Replace Repair or replace (After clean) Replace Replace Repair or replace (After clean) Replace Repair or replace (After clean) Repair or replace (After clean) Replace Replace Check voltage between CN-116 (4) an Intermittent Check voltag CN-116 (4) an d chassis Check voltag e CN-116 (12) and cha ssis 6-37 6-37