Komatsu — 4.7.6.D CHANGING THE HYDRAULIC SYSTEM OIL FILTER

MAINTENANCE PLAN 169 4.7.6.d CHANGING THE HYDRAULIC SYSTEM OIL FILTER WARNING • Soon after the machine has been stopped the hydraulic oil is very hot; let it cool down until it reaches a temperature of 40-45°C (104-113°F) before changing it. • The hydraulic system is pressurized; loosen the filling cap slowly to release the residual pressure. • Oils, filters, the coolant and the battery are considered 1 special waste and must be collected and disposed of ac- cording to the anti-pollution regulations in force. The filter is positioned on the hydraulic system drain outlet and blocks the metal particles that come off the various components due to their wear.

The filter can be reached after opening the engine hood; to change it, proceed as follows: 1 - Rotate the seat forward (See “3.5.5 SEAT”). 2 - Slowly loosen the filling cap (2) in order to release the residu- al pressure from the tank. RWA06240 Use a 24 mm hexagon spanner. 3 - Unscrew the used filter (1) with the special spanner provided and throw it away. 4 - Clean the contact surface between the seal and the filter sup- port, lubricate the seal of the new filter and screw it until it touches the support. 5 - Give another half turn by hand. IMPORTANT • Do not use the spanner to lock the filter, in order not to damage it and not to cause oil leakages.

6 - Move the seat to its normal position. RWA06730 7 - Extend the boom, arm and bucket cylinders completely, as in- dicated in the figure, and remove the filling cap (2). Put back the cap and pressurize the inside of the tank lowering the equipment to the ground. IMPORTANT 500 Replacement interval • The hydraulic oil used in machines provided with demoli- 400 for element Replacement (H) tion hammer deteriorates sooner than the oil used in ma- chines that carry out only normal digging operations.

200 interval On new machines the filter must be changed after the first 100÷150 hours of operation, while the successive chang- es must be carried out according to the intervals indicated 0 20 40 60 80 100 on table beside. Breaker operating ratio (%) RWA07520 1 WARNING • Soon after the machine has been stopped the hydraulic oil is very hot; let it cool down until it reaches a temperature of 40-45°C (104-113°F) before changing it. • The hydraulic system is pressurized; loosen the filling cap slowly to release the residual pressure.

• Oils, filters, the coolant and the battery are considered special waste and must be collected and disposed of ac- cording to the anti-pollution regulations in force. The filter is positioned on the hydraulic system drain outlet and blocks the metal particles that come off the various components due to their wear. The filter can be reached after opening the engine hood; to change it, proceed as follows: 1 - Rotate the seat forward (See “3.5.5 SEAT”). 2 - Slowly loosen the filling cap (2) in order to release the residu- al pressure from the tank. Use a 24 mm hexagon spanner. 3 - Unscrew the used filter (1) with the special spanner provided and throw it away.

4 - Clean the contact surface between the seal and the filter sup- port, lubricate the seal of the new filter and screw it until it touches the support. 5 - Give another half turn by hand. RWA06240 RWA06240 IMPORTANT • Do not use the spanner to lock the filter, in order not to damage it and not to cause oil leakages. 6 - Move the seat to its normal position. 7 - Extend the boom, arm and bucket cylinders completely, as in- dicated in the figure, and remove the filling cap (2). Put back the cap and pressurize the inside of the tank lowering the equipment to the ground.

RWA06730 500 Replacement interval 400 for element Replacement (H) 200 interval 0 20 40 60 80 100 Breaker operating RWA06730 500 Replacement interval 400 for element Replacement (H) 200 interval 0 20 40 60 80 100 Breaker operating IMPORTANT • The hydraulic oil used in machines provided with demoli- tion hammer deteriorates sooner than the oil used in ma- chines that carry out only normal digging operations. On new machines the filter must be changed after the first 100÷150 hours of operation, while the successive chang- es must be carried out according to the intervals indicated on table beside. ratio (%) RWA07520 ratio (%) RWA07520 Replacement interval for element