Plug connections 1 MES O Activation for fuel-delivery actuator Output, fuel-delivery control circuit I max 11 A temporarily, on average 4.5 A, against batt.+, pulsded, f=variable, pulse-width modulated 2 MES O Activation for fuel-delivery actuator Output, fuel-delivery control circuit 3 VHS O Pre-stroke actuator activation Output, start of delivery control circuit I max 6 A temporarily, on average 3 A, against batt.+, pulsed, f approx. 200 Hz, pulse-width modulated 4 VHS O Pre-stroke actuator activation Output, start of delivery control circuit 5 MBR 1 Engine brake actuator Output (switch) I max 2 A, U batt. against batt. –, 6 LEB 1 Air injection Output (switch) I max 2 A, U batt.
against batt. –, 7 WGS 1 Waste gate Output (switch) I max 1 A, U batt. against batt. –, 8 LKS 1 Intercooler bypass Output (switch) I max 1 A, U batt. against batt. –, 9 RWG M Control rod position transducer measuring coil (RWG 2) Control rod position evaluator circuit 10 RWG R Control rod position transducer reference coil (RWG O) Control rod position evaluator circuit 11 RWG Y Control rod position transducer centre pick–off (RWG 1) Control rod position evaluator circuit 12 CAN O Reference ground for CAN H/L 13 GND-A Sensor ground 14 EAB 1 Electrical shut-down Output (switch) I max 1 A, U batt. against batt. –, 15 Batt.+ Batt.
+ via main relay Input battery + I with engine stationary 0.9 A, idle speed 1.5 A, operation 4.5 A, temporarily 16 A 16 Batt.+ Batt. + via main relay Input battery + 17 NBF 0, HZGO Needle movement sensor and auxiliary rpm sensor Reference ground: 18 Batt.– Battery negative Input battery – I Same as batt.+ (terminals 15 and 16) 19 Batt.– Battery negative Input battery – 20 DIA-B Diagnosis lamp Output (switch) I max 1 A, U batt. against batt. –, 21 DZG 1 RPM sensor signal Input, dynamic Alternating voltage U pp idle speed approx. 2 V, max. 80 V, f=number of cyl. X N sec. 22 HZG 1 Auxiliary rpm sensor signal Input, dynamic Alternating voltage U pp idle speed approx. 2 V, max.
80 V, f=number of cyl. X N sec. 23 ZDR-E1 Intermediate engine speed control 1 Input, static Batt. + 24 BRK-E Brake switch signal Input, static Batt. + 25 FMS-E Function-mode switch FGR/FGB Input, static Batt. + 26 KUP-E Clutch switch signal Input, static Batt. + 27 PWG 1 Pedal position sensor signal Input, analog Direct voltage, U approx. 0.4 to 4 V 28 TDS-A Engine speed signal Output U batt. against batt. –, square-wave signal, f=number of cyl. X N sec. 29 MPS-A Multiplex signal Interfaces 30 CAN-L Controller Area Network Interfaces 31 CAN-H Controller Area Network Interfaces 32 NBF 1 Needle movement sensor Input, dynamic U pp approx.
2 V 33 LDF 2 Turbo pressure sensor Output, supply Controlled direct voltage, U approx. 5 V 34 KTF 1 Fuel temperature sensor (used for charge air temperature) Input, analog 35 MDB 1 Multi-stage input (torque limitation) Input, analog Input by change in resistance 36 LDF 1 Turbo pressure sensor signal Input, analog 37 FGB 1 Driving speed limit lamp Output (switch) I max 1 A, U batt. against batt. – 38 EOL E Input, static 39 LGS-E Idle speed switch signal Input, static against GND-O (terminal 13) Pin No. Abbreviation Description 129