TwinFlow Fire Pump 90.00 Fire Pump Gearbox Removal, Disassembly, Assembly, and Installation CAUTION 2.9 Slide the input shaft through the output shaft housing opening at the rear of the transmission through the drive gear, the thrustwasher, the bearing cones, and spacer(s). Bearing cups, cones, and spacers are factory pre-set for end play, and are only provided as a matched set. It is important that bearing cups, bearing cones, and spacers, when removed, be kept together in matched sets. Input and output shaft bearing and spacer sets are different.
Fail- ure to keep matched sets together or to not use factory pre-set and matched bearing and spacer sets will void the warranty and may result in gearbox failure. 2.10 Install the front driveline yoke on the input shaft, being careful not to damage the in- put shaft seal. Apply Loctite ® 242 to the 3/4–10 x 1-1/2 yoke capscrew. Install the capscrew and washer, then tighten them to 225 lbf·ft (305 N·m). NOTE: Apply a coat of Loctite to all screws prior to reassembly. 2.1 Using a brass drift or a bearing cup instal- lation tool, install the inner bearing cup from the inside out. Then install the spac- er(s) and insert the retaining ring. NOTE:
One ear of the shift yoke is ma- chined, and it will only fit one way. Make sure the yoke is oriented on the shaft in the position noted during disassembly. 2.2 Using a brass drift or a bearing cup instal- lation tool, install the outer bearing cup from the outside in. 2.11 Make sure the shift fork is properly aligned (the machined side should be toward the threaded end of the shift shaft), then slide the new shift fork on the shift shaft. Align the shift fork with the groove in the shaft, then secure the shift fork in place with a 3/8–16 x 1-1/4 screw. Tighten the screw 33 lbf·ft (45 N·m). 2.3 Coat the outer bearing cone with oil. In- stall the outer bearing cone.
2.4 Install the input shaft seal. 2.5 Install the windage tray positioning springs and windage tray. While holding the wind- age tray in place against the positioning springs, install the windage tray position- ing pins. 2.12 Install a new seal on the shift shaft sup- port block. Install a new gasket on the shift shaft support block. Install the shift shaft support block and gasket in the gearbox using two 1/4–20 x 5/8 cap- screws. Tighten the capscrews to 96 lbf·in (1085 N·cm). CAUTION There are two bearings of different widths sup- porting the drive gear on the input shaft. It is im- portant that these bearings be installed in the drive gear in the proper location.
The location of the bearings should have been noted when re- moved from the assembly. Make sure that the lu- brication holes are aligned in the center of the larger bearing. Failure to install the bearings properly may result in gearbox failure. 2.13 Place the shift ring into the shift fork grooves. While holding the shift ring in place, insert the shift shaft into the gear- box through the bushing. Make sure the teeth on the shift shaft ring line up with the teeth on the input shaft and gear. 2.14 Apply a light coating of grease to the new seal ring, then install the seal ring on the shift piston. Install the piston on the shift shaft end.
2.6 Coat the new drive bearings with oil, then install the bearings in the drive gear. 2.7 Coat the inner bearing cone with oil, and install it. Then, install the thrustwasher. 2.8 Reaching through the top of the transmis- sion housing, install the drive gear in posi- tion against the thrustwasher, being care- ful not to dislodge the windage tray. CAUTION When installing the piston, use a new locknut and tighten snugly but do not overtighten. Over- Business Class M2 Workshop Manual, Supplement 8, September 2005 110/6