Engine Operation 74 UENR4490-01 i05934639 Glossary of Electronic Control Terms Cold Mode – Cold mode is a mode for cold starting and for cold engine operation. This mode is used for engine protection, reduced smoke emissions, and faster warm-up time. Communication Adapter Tool – The communication adapter provides a communication link between the ECM and the Electronic Service Tool. Active Diagnostic Code – An active diagnostic code alerts the operator or the service technician that an electronic system malfunction is currently present. Refer to the term Diagnostic Trouble Code in this glossary.
Coolant Temperature Sensor – The coolant temperature sensor detects the engine coolant temperature for all normal operating conditions and for engine monitoring. Aftertreatment – Aftertreatment is a system that is used to remove pollutants from exhaust gases. The system consists of a Diesel Oxidation Catalyst (DOC), a Diesel Particulate Filter (DPF), and a Selective Catalytic Reduction (SCR) system. Customer Specified Parameters – A customer specified parameter is a parameter that can be changed in the ECM with the Electronic Service Tool. A customer specified parameter's value is set by the customer. These parameters are protected by customer passwords.
Air-To-Air Aftercooler – An air-to-air aftercooler is a device that is used on turbocharged engines in order to cool inlet air that has undergone compression. The inlet air is cooled after the inlet air passes through the turbocharger. The inlet air is passed through an aftercooler (heat exchanger) that uses ambient air for cooling. The inlet air that has been cooled advances to the inlet manifold. Data Link – The Data Link is a serial communication port that is used for communication with other microprocessor-based devices. Alternating Current (AC) – Alternating current is an electric current that reverses direction at a regular interval that is reoccurring.
Derate – Certain engine conditions will generate event codes. Also, engine derates may be applied. The map for the engine derate is programmed into the ECM software. The derate can be one or more of three types: reduction of rated power, reduction of rated engine speed and reduction of rated machine speed for OEM products. Ammonia Oxidizing (AMOX) catalyst – The AMOX catalyst removes any residual ammonia from the exhaust gas stream after completion of the Selective Catalytic Reduction (SCR) process. Desired Engine Speed – The desired engine speed is input to the electronic governor within the ECM.
The electronic governor uses the signal from the throttle position sensor, the engine speed/timing sensor, and other sensors in order to determine the desired engine speed. Before Top Center (BTC) – BTC is the 180 degrees of crankshaft rotation before the piston reaches the top center position in the normal direction of rotation. Inlet Manifold Pressure – The difference between the turbocharger outlet pressure and atmospheric pressure is commonly referred to as inlet manifold pressure. The sensor for the inlet manifold air pressure measures the amount of boost. Diagnostic Trouble Code – A diagnostic trouble code is sometimes referred to as a fault code.
These codes indicate an electronic system malfunction. Breakout Harness – The breakout harness is a test harness that is designed to connect into the engine harness. This connection allows a normal circuit operation and the connection simultaneously provides a Breakout T in order to measure the signals. Diagnostic Lamp – A diagnostic lamp is sometimes called the check engine light. The diagnostic lamp is used to warn the operator of the presence of an active diagnostic code. The diagnostic lamps are red and orange. The lamp may not be included in all applications. Bypass Circuit – A bypass circuit is a circuit that is used as a substitute circuit for an existing circuit.
A bypass circuit is typically used as a test circuit. Diesel Exhaust Fluid (DEF) – DEF is a mixture of urea and water that is injected into the exhaust stream. The heat in the exhaust gas releases the ammonia in the DEF. The ammonia reacts with the oxides of nitrogen (NOx) in the SCR filter to produce nitrogen and water vapor. CAN Data Link (see also J1939 CAN Data Link) The CAN Data Link is a serial communications port that is used for communication with other microprocessor-based devices. Clean Emissions Module (CEM) – Refer to Aftertreatment . Diesel Oxidation Catalyst – The DOC is a device in the exhaust system that oxidizes certain elements in the exhaust gases.
These elements can include carbon monoxide (CO), hydrocarbons and the soluble organic fractions (SOF) of particulate matter. Code – Refer to Diagnostic Trouble Code .