Perkins — Perkins 1204F-E44TA and 1204F-E44TTA Industrial Engine Systems Operation Manual

Engine Operation 76 UENR4490-01 Dosing Control Unit (DCU) – The DCU controls the injection of Diesel Exhaust Fluid (DEF) into the exhaust gas stream. the parameter identifier (PID) in the descriptions of the fault code. The descriptions of the FMIs are in the following list. DT, DT Connector, or Deutsch DT – This is a type of connector that is used on the engines. The connectors are manufactured by Deutsch . 0 – The data is valid but the data is above the normal operational range. 1 – The data is valid but the data is below the normal operational range. Duty Cycle – Refer to Pulse Width Modulation . Electronic Engine Control – The electronic engine control is a complete electronic system.

The electronic engine control monitors the engine operation under all conditions. The electronic engine control also controls the engine operation under all conditions. 2 – The data is erratic, intermittent, or incorrect. 3 – The voltage is above normal or the voltage is shorted high. 4 – The voltage is below normal or the voltage is shorted low. Engine Control Module (ECM) – The ECM is the control computer of the engine. The ECM provides power to the electronics. The ECM monitors data that is input from the sensors of the engine. The ECM acts as a governor in order to control the speed and the power of the engine. 5 – The current is below normal or the circuit is open.

6 – The current is above normal or the circuit is grounded. 7 – The mechanical system is not responding properly. Electronic Service Tool – The electronic service tool allows a computer (PC) to communicate with the ECM. 8 – There is an abnormal frequency, an abnormal pulse width, or an abnormal time period. Engine Monitoring – Engine Monitoring is the part of the electronic engine control that monitors the sensors. This also warns the operator of detected problems. 10 – There is an abnormal rate of change. 9 – There has been an abnormal update. 11 – The failure mode is not identifiable. Engine Oil Pressure Sensor – The engine oil pressure sensor measures engine oil pressure.

The sensor sends an electronic signal to the ECM that is dependent on the engine oil pressure. 12 – The device or the component is damaged. 13 – The device requires calibration. 14 – There is a special instruction for the device. Engine Speed/Timing Sensor – An engine speed/ timing sensor is a hall effect switch that provides a digital signal to the ECM. The ECM interprets this signal as the crankshaft position and the engine speed. Two sensors are used to provide the speed and timing signals to the ECM. The primary sensor is associated with the crankshaft and the secondary sensor is associated with the camshaft. 15 – The signal from the device is high (least severe).

16 – The signal from the device is high (moderate severity). 17 – The signal from the device is low (least severe). 18 – The signal from the device is low (moderate severity). Estimated Dynamic Timing – Estimated dynamic timing is the estimate of the actual injection timing that is calculated by the ECM. 19 – There is an error in the data from the device. 31 – The device has failed and the engine has shut down. Event Code – An event code may be activated in order to indicate an abnormal engine operating condition. These codes usually indicate a mechanical problem instead of an electrical system problem. Flash File – This file is software that is inside the ECM.

The file contains all the instructions (software) for the ECM and the file contains the performance maps for a specific engine. The file may be reprogrammed through flash programming. Exhaust Back Pressure Regulator – The exhaust back pressure regulator regulates the gas pressure in the exhaust system. The valve can restrict the flow of exhaust gases in order to increase the exhaust back pressure. An increase in exhaust back pressure will increase the temperature of the exhaust gases. The increase in temperature will improve the process that burns off the soot in the DPF.

Flash Programming – Flash programming is the method of programming or updating an ECM with an electronic service tool over the data link instead of replacing components. Failure Mode Identifier (FMI) – This identifier indicates the type of failure that is associated with the component. The FMI has been adopted from the SAE practice of J1587 diagnostics. The FMI follows Fuel Injection Pump – This item is sometimes referred to as the High Pressure Fuel Pump. This is a device that supplies fuel under pressure to the fuel