PtPER COMANCHE SERVICE MANUAL by removinj( cotter pin. nut. wuber and ,clevis bolt or by disulemblin, the turnbuckle. 4. Remove the cotter pin cable pard from the cable pulley by racbitlJ tbroulh the access hole in each wing at sation 115.50. S. Remove the cotter pin cable pards from the left and riJbt puOeys of the bal&ncc cable at fusclace sution 13$.0. 6. If an AutoPilot roU servo is a.a:adlal to the bl1ancc cable. remove the slot bead screws from the bridle cable clamps at the center of the fue Remove the safety slcna iIlboard of each clamp. 1. Draw the cable throUJh the fuselap ad each wiDJ. Usc caution _heD drawiaJ the end of the cable through the rub block at wiftJ sation 78.0. &.
Installation of the aileron balance cable may be accomp1isbecl by the foUowillJ procedure: 1. Draw the baJance cable (4) into each wiDe from the center of the f\ISc1qc. 2. With the cable positioned on both the left and rilht puOeys ill the fusclace at station 135.0. insull the cotter pin able JUUds. 5·10. IosaI1a1:iOft Of ADINIl CODenl Cabla. (Refer to Fipre '·2.) 3. Amch the ends of the cable to the forwud end of the beUc:rank in each willi by assemblinr nunbuc:kJes and/or sccurinJ with clms bolt. waber, nut and cotter pin. Do not set cable tension at this time. NOTE Do not tiJhten aambuckle fork ends Oft bellcruak so a,ht that tbe end cannot rotate. 4.
By rftChinl throUJh the access opcnin, in each willi at nation 115.5. position the able uound the upper puOey of the cluster and if the primary control cable i. iastaUed. insall the cotter pill cable guard. 5. If an autopilot roD 1CtY0 is part of the airplane's equipment. attach the bridle cable to the balance cable with the usc of the iDRallation inm\IetiODl pen in ElectrOnics Section. b. Installation of the left andlor ",ht primary contrOl cables (3 and 6) thu lad from the fuselage into the winp may be accomplished by the foUowiDJ procedure: 1. Dnw the cable throup the wint intO the twc ... 2. Install the cable puUey in the fuse forward of the rear spar suppon bulkhead at sution 135.0.
For the left pulley, position the cable and' puDer and secure with bolt, wubcr and GUt. For the riPt pulley. position the cable and puUey in the bracket and _CUR puUey with bolt. wubcr and nut. and then attach the bracket assembly to the bortom skin of the fUsdatc and spar suppan bulkhead usinJ screws. Ascertain that corter pin cable pards 1ft installed. 3. If the right cable (6) was removed. position the cable and instaU the pulley in the bncket located on the butt aft end of the wiftl by usi.nI bolt, wabet and nut. 4-. Tbroqh the access hole in the wiDe at station 115.5, position the cable on the lower pulley of the cluster and install the corter pin cable pard. ,.
Attach the cable to the aft end of the cable bcUcrank by asscmblinl turnbuckle and/or securing with clevis bolt. wuhcr. nut ad cotter pin. NOTE Do not tilhten turnbuckle fork end. on the bcllcrank so titht that the end cannot rotate. SURFACE CONTROLS ISSUeD: 8118n2 IGI