BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COMANCHE SERVICE MANUAL L To rig the aileron controls. set the aileron bellerank in ncurral by posirioninl ~ sperl&! alifnint tool within the wing as shown in Fiaure '-3. (This tool may be fabricated from dimensionllivCJl in Fipre '-13.) The tool (Side A) usa the inside JUnac" of rat ifill' u reference. A.lip Side B with centerlines of the bdlcr&nk amchint bolt and tumbuc.k1e uuchinr bolt. b. With the bellerank in neutral polition. alip the trailinI cdte of the aileron with the craili", edp of the flap. by adjustinl the aileTOn contrOl rod. Ascertain that the flap it fully mractcd. (Refer to puqn.ph '-U. '-19. '·23) Repeat this proccQure for the other aileron. c.

Place a b~bble promeror on the aileron. perpendiculu to the hiqeline. and adjust the bcUcrank stOp bolts to srttific aileron travcl from neutnl. (Refer to Table V-I and Fiplt 5....) d. With the aileron and bcl1cnnk in DCUual. 1ft cable tension (Refer to Table V-I) to maintain horizontal alianmcnt of the lower surface of me conaol whcdL The aileron bcUCI'Ulks must hit the bcllcn.nk stop before the control whcci hits its atoPI. '-11. RiFIAnd Adjuanent Of Aileron Conerol. e. On PA·24-260 Scria.I NOI. 24-4783. 2......,04 and up. and PA·2400400 airaaft.

set the naddct-ai1eron ineereeaaeee able cumbuc.k1e (11) (Refer to Fiture 5-2), 10 that the Iup .priDt (18) hu .062 inch extension when the Ndder and ailerons are 1ltNtral. On the PA-24-260 syaem the ICftJth of the left intcrcoMect sprins (19) may be incrased up to a maximum atasion of.38 to allow the aileron controls to spring back approxim&te equal amounts from ",ht aDd left scops with the rudder controls hdd in ncutn.I position. 5·12. Manually Oper.ted Flapl. a. The flap Icver assembly (36) may be removed by liftint the Door panel to the control mechanism• disconnecting the control cable and the contrOl attaebinc screws. '-13. Removal Of MuluaUv Operated Flu Concroll.

(Refer to Filrwe 5-5.) b. The control cable (40) located within the tusclate may be removed by rcmovinc the reu seat. disccnncc'ting the tumbuckle beTWccn fuselqe cable and winl cable. Dn.w the cable &om beneath the floor pand. c. To remove the cable that leads from the fusclqe to the wing. disconnect conuol cable at the bellcrank and draw the cable from the wing. d. Remove the flap bdlcrank by discoMecti", the flap control rod and removing bolt securing the bellerank. a. Install the flap beUcrank. sccure the pivot bolt to a snug fit and connect the rctum spring. Ascertain that the lock operates properly and connect the flap control ann. b.

Draw the right or left contrOl cable into the winI and connect to the bellcrank. c. Connect the fuselqe control cable (40) to the wing cable at the rear Seat location ~nd draw the cable benC&th the floor panel to the location of the flap handle (36). Secure cable guards and pulleys. d. Install the flap lever and connect the concrol cable. Rig and adjust per pa.racnph '-15. '·14. InlUJlation Of Manually Operated Flap Coacrob. (Refer to Figure '-'.) '-15. Rilling And AdjuStment Of Manually Operated Flap ContrOls. a. To adjUst flap controls. ascertain that the flap bellcrank cateh is engaged. Adjust flap control rod to allow flap to position in neutral. b. To obtain specific travel.

adjust each flap cable eurnbuckle, Check the operation of the flap and that the nap lock engages properly. Refer to Table V-I for degrees of travel. SURFACE CONTROLS ISSUED: S/1Sn2 IG5