BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COM:\~CHE SERVICE MA~L\L fI-~. ~ose landing Gear. fI-fl. Disassemble Of :\ose Gear Oleo. (PA-24-1l' and Pf\-24-250. Serial 'o~. 24-1 to 24·214 inclu-ive.t t Rctcr to r igurc e-L) ThL' nove gl'ur oleo a ...... ernbly may be removed and di ... assembled from the gear llk,l hou-ing \\ ith the gear removed from or installed on the airplane. a. Place the airplane on jacks. (Refer to Jacking. Section 11.) h. Place a drip pan under the gear to catch spillage, c. Remme the air and fluid Irorn the oleo. To do this. depre ... s the air valve core pin (4) until -trut prc-vure ha ... diminished. remove the filler plug (5). and with a small ho ...

e siphon as much hydraulic fluid from the strut as po ... sible. d. To remove the pi ... ton tube a ernbly (12) from the oleo housing IJI. remove the upper (Ul and 100\er ( 15) torque link connecting bolt as crnbly (14) and separate the links. xote the upper and lower torque link- and t hc number of ... pacer w a ... her between the two links. e. Cornprc- ... the pi ... ton tube ( J 2). reach up along the tube and release the snap ring (J J I from the annular ... lot at the bottom of the oleo housing. f. Pull the pi ... t on tube \\ ith component part- from the cylinder housing. g. The ri ... ton t ube component- may be removed by reaching in the tube and pu ...

hing nut t he upper bearing rcta i ner pin ... (241. Slid e off the upper bearing (25). spacer (26). lower bearing (:!7) with in ne rand outer "0" ring ... I ~4 and 2~1. \\ iper e9). \\ u ... her (30) and snap ring (3 J). h. To rcmov e the orifice tube (:! II from the oleo housing. remove the locknut ( I) and \\ asher (2 l from the top of t he hou ... ing. Draw the tube with "0" ring (20) and back-up washer (19) from the hou-ing. i. Th L' orifice plate (22\ is removed from the bottom of the orifice tube bv relea..ing the -nap nng 123) that hold, t hc plate in position i. T l) r cmov I.' t he pi-ton tube plug (~~l \\ ith "0" ring (33) located in the lower end of the tube.

rcrnnv c the holt a"emhly and in ... ert a rod up through the hole in the body of the fork (181. pu..hing the plug out through thL' tl)P 01 the tube. fl-~. Cleaning. Inspection And Repair Of :\ose Gear Oleo. a. Clean all part- wit h a ... unable quick drying type cleaning solvent. h. In..pcct the landing gear oleo as..ernbly component for the following: I Bearing and hu ... hing ... for excess wear. corrosion. scratches and overall damage. ... Retaining pin~ for wear and damage . . ~. l.ock ring ... for cracks. burrs. etc. 4. C~ linder and orifice tube for corrosion. scratches. nick- and excess wear. 5. Orifice plate for hole restriction. t», For], tube for corrosion. scratches. nicks.

dents and misalignment. Air valve general condition. l'o. Worn or broken turning limit stop .... If the no-e \\ heel turning limit stops are found broken or have been broken in the pa ... t. the entire system including the following items should he checked to insure proper rudder action and condition: (al Check rudder hinges. pulleys and pulley brackets. (hI Check rudder rigging and cable tension per instructions in Section \ of thi ... manual. RE\'ISED: ~/ 10/81 IH23 lA~DI~G CEAR .-\.:\D BRAKE S\'STE\1