BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COMANCHE SERVICE MANUAL e. Compress the piston Nbc (8), reach up alOnt the Nbc and rele:uc the snap riDf (29) from the annular slot at the bottom of the oleo housinc. f. Pull the fllston Nbc with component puts from the ~lindct hOusiDJ. g. The piston tube componentS may be removed by reaching in the Nbe and pushinJ Outthe upper bearins retainer pins (23), Slide off the upper bcui.r11 (12), lower bearin, (Z4) with "0" tinas (25 alid 26), wiper (27). washer (28) and snap riftl (29). h. To remove the orifice tube (19) from the oleo bouu remove the locknut (12) and wuhcr (13) from the tO~ of the housinl.

Draw the tube with back·up riDa (1.), "0" Me (15) and rinI (16) (PA-24-400 only) from the housing. I. The orifice plate (17) is removed &om the bottom of the orifice cubc (19) by releasing the snap rin, (18) that holds the plate in position, Expand lnd remove the riq (16) from the lower eDdof the Nbe. j. To remove the piston tube plug (21) with "0" nn, (20) located in the lower end of the piston tube (8), remove the bolt assembly (9) and insert a rod up throuF the hole in the body of the fork (1), pushing the plul out through the tOP of the rube, 6-29. C1cuainl. Inspection And R.epair Of MaiD Gar Olco. a. Clean all parts with a suiuble dry tYpe c1a.aiD1 solvent. b.

Inspect the landinl,ear oleo assembly component for tbc'foUowing, 1. Scarinp and bushinp for excess wear, corrosion, scratches and overall damage, 2. Rcu.inina pins for WClt and damqc. 3. Lock rinp for cracks, burrs, etc, 4-. Cylinder and orifice Nbc for corrosion. sc:ntches, nicks and excess wear. 5. Orifice plate for bole t'Csmcnon. 6. Fork.tubc for corrosion. scratches, nicks. dena and miJalipment. 7. Air valveJencra1cOlldinon. c. Repair of the oleo is limited to smoothilll out minor scratehes. nicks and denu and replacement of parts. d. Individual replacement of wiper strips may be accomplished per instructions Jiven in parqraph 640. 6-30. Auembly Of Main Gar Oleo.

(Refer to Figure 6~.) a. Ascertain that all pans are cleaned and inspected. b. To install the piston tube plul (21), fust lubricate the plug "0" rint CZO) with hydraulic fl~id (MIL-H-5606) and instal! it on the plug. Lubricate the inside wall of the piston tube (8). Insert the pl\&l,into the tOp ot the tube and push it to the fork end. AllIn the bolt bola of the fork, tube and pllJl' and install bolt assembly (9). (If a new Nbe (8) is installed that bas not been cirilled. press the tube into the fork ho~sing until it bottoms. Using the fork bolt holes u a pidc. drill a pilot hole and ream to 0.250/0.252 thro~gh each side of the tIIbe wall.

Remove bum &om the inside of tbe rube and flush the tube with a suitable solvent to remove all mccal particles. c. If desired. cement a cork in the hole in the bottom of the fork body to prevent dirt from entering between the fork and tube. d. To assemble the compcneau of the orifice tube ( 19), insert the orifice plate (17) into the bottom ot the tube and secure with snap ring (18). Insull ring (16) (PA-24-1-OO only) on the lower end of the tube. e. To install the orifice tube in the oleo housiftl (7). insert the Nbe up through the ho~sing. With the end of the tube exposed through the top of the housinl. install the "0" ring (15), back-up ring (140), washer (13), and locknut (12).

TiJhten locknut only iinSCf tiJht at this nme. LANDING GEAR AND BRAKE SYSTEM ISSUED: 8/18172 1117