PIPER COMANCHE SERVICE MANUAL a. To remove the prCSIUre screen, remove oil tel!1perature electrica1lead or the temperarure bulb and the C:lp screws sccunng the housing. :"Jote the location of the screws u the round fillister head saew, if installed. must be returned to upper right comer of the housinS' If the (illister head screw is not reinstalled in rne same hole from which it wu removed. it is impossible to crack the mounting flange of the vacuum pump. b. With the housin. and screen removed. clean and inspect both items. check the mating surface of the housing and accessory case of gasket particles. c. Insert the screw intO the housin, so that the screw fits flush with the housing base.
Vsing a new guket. secure the housing to its mountitIJ pad and torque cap screws to 15 inch pounds. d. The suction screen il. removed from the sump by rernovinJ the hex head plUl at the lower ait put of the sump. Clean and inspect the screen and ,uket, replace the ,asket if over compressed or dama,ed. Insert the screen fully intO the sump. install psket and plug. Safety the plug. '7-56. Oil Cooler. a. When conducting a routine engine inspection. the oil cooler(s), lines and Јiteinis shouid be checked for the follOWing: 1. Oil cooler line attachments should be examined to be Certain that all are tliht and there is no Indication of cross-threading. (See C for oil line torque.) 2.
Oil lines must have adequate cleannce and be properly alifned. 3. 011line supportS should be tight. properly positioned and if wom should be replaced. ... 011cooler should be checked for lealcqc or distorted cells. S. Cooling fins should be clean and undama,ed. b. During each engine overhaul. at indication of high oil tempentures or during a 500 hour inspection. the oil cooler should be removed. cleaned and checked for dam.,ed fins and cells. Wh=n replaCIng the cooier. properiv align and do not over tighten the mounting bolts so that the cooler would be damaged. While the oil cooler is removed. the oil linn should be disconnected and flushed. c.
If it is found that 011 is lcalung around the line compression nuts. check that the nuts are tightened to 125 inch pound wet torque or the nut may be backed off, reti.htened fiRJer tight. plus a 3/4 tum. Do not Olver torque. d. Should oil continue to leak. it may be necessary to replace the seal rings. Also remove the compression nuts and Inspect the line ends in the area of the swaged femdes for collapsed tubing. This condition may be observed by looking into the rubini ends. Should the tubing show indicanons that It is collapsed and new seal rings and proper torque does not stop leakage. the oil lines should be replaced. Also Inspect the surfaces of the matin~ fittings for damage. 7-57.
Recommendations For Chanline on. (Ref. latest Lye. S.l. No. 1014 ) a. If an additive oil is used in '" new engine. or a newly overhauled engine. high all consumption might possibly be experienced. The anri-fricncn additives of some of these oils will retard the break-in or the piston rings and cylinder walls. ThIS condinon is euily corrected by the use of straight minerai oil unnl normal oil consumption 15 obramed, then change to the additive type. b. In engines that have been operating on Str:aight mineral oil for more man 100 hours. 1 chanse to detergent oil snould be made WIth a degree of caution.
the cleaning action of a detergent oil will tend to loosen siudge deposits anci cause ?Iuggcd oil passages. In fact. if an engine hu been operating on strai!lnt mlnerJ.i oil. and 15 known to be In excessivelv dirty condition. the switch to detergent oil should be defe; ed until afrer tne englnc lS overhauled. POWER PLANT REVISED: 4/10/81 2 819