BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPER COMANCHE SERVICE MANUAL 9-14. DI ....... ltly, R.poit And R ....... ltly. Normally, dis.sembly should procMd only so far as is necessary to make repair or replacement of the defective part For 8:lample, the field coils should be checked for opens, shorts. or IfOWld. before beiDl c.moved &om the field frame: they should be removed only if they require repair or replacement. 9-15. Field C.lI R ....... I. Field coil. can be removed from the field frame taMt e .. ily by IIle of a pole shoe screw driver. It 'I alIa advisable to .... a pol. sboe .preader, .iDee this prevents distortion of the field frame.

The pole sboe .crew driver penaits euy l~eaial and removal of the pole shoe .crews so that the pole shoes lIftd field coil. CaD be taken out of the field frame. The pole shoe .Cntw driver and spreader should be used oa re mbly of the field frame. Careful re .. sembly i. lleces.ary to prevent sbortinl or IfOUIldinl of the field coils .. the pole sboes are tilhttfted into place. a. The arm.nue or field should 1I0t be clellfted in eay depe_ial teak or by use of deere .. ini compounds, .ince tbis mieht dama. insulation so that I .hurt or IfOUftd would subsequently de- velop. Sealed ball beannls do 1I0t require cleeailll or relubrication. Other lenerator part.

should be cleaned and carefully inspected for we., and other dam.... ADy defective parts should be repaired or replaced. On reas.mbly aU sold.red electrical connections Ihould be lude with ro.in flux. Acid flux mu.t never be u.ed on electrical COlUlectioaS. 9-16. Inspectlo" Ancl R.poir Of PlittS. 9-17. Fi.lcI Coli. a. The field coil. should be checked for pouad., opens or shorts a already explained in paragraph 9-10. b. Grounded field coil. may sometim.. be repaired by removinl them 10 th.y can be reinsu- lated. Care must be used to avoid exc ...

ive bulkin when Ipplyinl Dew insul.tion, ,iace this mieht cause the pole shoe to cut throulh and cal&se Mother &fOund when the coils are reinstalled. c. Usually. if a field coil is open or shorted intlmal!y it will require replacement, .ince it is difficult to repair such I defect. d. To remove or replace field coil. in the field frame, the u.e of I pole .hoe sprelder and screw driver is recommended. 9-18. Armatur. Se"ice. a. The annature .hould be checked for opena, shorts and IfOWlCls a. explained ill followini p.ragraphs. If the armature commutator is wom, dirty, out of round, or h ..

hip lIIica, the armature should be put in a lathe so the commutator can be turned down and the mica unden:;.ut. The mica should be undereut li32 of an inch and the .lotl cleazsed out carefully to telIIove any trace of dirt or copper dust. As a fillSl step in this procedure, the commutator should be .anded lilhtly with No. 00 sandpaper to remove any slilht burrs that llIipt be left a result of the Llildercuttillg procedure. b. Open cireuited arm.tures can often be s.ved when the open is obvioul and rep.irable. The most likely place an open will occur is at the cOllllllutator riser bars: this ulu.lly results from overloadinl of the pIlarator, whieh caul ..

overheatiftl and meltinl of the solder. Rep.ir can be effected by feselderinl the lead. in the riler bars (Ulinl rMin flux) and tuminl down the com- mutator in a lathe to remove the burned spot ud then \lDdercuttial the mica IS explained in the previous par'lraph. 111 some heavy-duty· armatures the l ds are welded into the ri.er b.rs, and these cannot. of course, be repaired by resolderinl. ELECTRICAL SYSTEM ISSU ED: 8/18/12 3 A19