C Series Troubleshooting Overview Section TS - Troubleshooting Symptoms Page TS-5 Engine noise can sometimes be isolated by performing a cylinder cutout test. If the volume of the noise decreases or the noise disappears, it is related to that particular engine cylinder. There is not a definite rule or test that will positively determine the source of a noise complaint. Engine-driven components and accessories, such as gear-driven fan clutches, hydraulic pumps, belt-driven alternators, air-conditioning compressors, and turbochargers, can contribute to engine noise. Use the following information as a guide to diagnosing engine noise.
Main Bearing Noise (Refer to the Engine Noise Excessive - Main Bearing troubleshooting symptom tree in Section TS) The noise caused by a loose main bearing is a loud, dull knock heard when the engine is pulling a load. If all main bearings are loose, a loud clatter will be heard. The knock is heard regularly every other revolution. The noise is the loudest when the engine is lugging or under heavy load. The knock is duller than a connecting rod noise. Low oil pressure can also accompany this condition. If the bearing is not loose enough to produce a knock by itself, the bearing can knock if the oil is too thin or if there is no oil on the bearing.
An irregular noise can indicate worn crankshaft thrust bearings. An intermittent, sharp knock indicates excessive crankshaft end clearance. Repeated clutch disengagements can cause a change in the noise. Connecting Rod Bearing Noise (Refer to the Engine Noise Excessive - Connecting Rod troubleshooting symptom tree in Section TS) Connecting rods with excessive clearance will knock at all engine speeds under both idle and load conditions. When the bearings begin to become loose, the noise can be confused with piston slap or loose piston pins. The noise increases in volume with engine speed. Low oil pressure can also accompany this condition.
Piston Noise (Refer to the Engine Noise Excessive - Piston troubleshooting symptom tree in Section TS) It is difficult to tell the difference between piston pin, connecting rod, and piston noise. A loose piston pin causes a loud double knock that is usually heard when the engine is idling. When the injector to this cylinder is cut out, a noticeable change will be heard in the sound of the knocking noise. However, on some engines the knock becomes more noticeable when the vehicle is operated on the road at a steady speed. Oil Consumption In addition to the information that follows, a service publication is available entitled Technical Overview of Oil Consumption, Bulletin Number 3379214.
Cummins Engine Company, Inc. defines “acceptable oil usage” as outlined in the following table.
Accetable Oil Usage Any Time During Coverage Period Engine Family Hours per Quart Hours per Liter Hours per Imperial Quart Miles per Quart Miles per Liter Miles per Imperial Quart Kilometer s per Quart Kilometer s per Quart Kilometer s per Imperial Quart A 10.0 10.6 12.0 400 425 475 650 675 775 4B 10.0 10.6 12.0 400 425 475 650 675 775 6B 10.0 10.6 12.0 400 425 475 650 675 775 6C 10.0 10.6 12.0 400 425 475 650 675 775 V/VT-378 4.0 4.3 5.0 - - - - - - V/VT-504 4.0 4.3 5.0 250 265 310 400 425 485 V/VT-555 4.0 4.3 5.0 250 265 310 400 425 485 L Series 4.0 4.3 5.0 250 265 310 400 425 485 M Series 4.0 4.3 5.0 250 265 310 400 425 485 N Series 4.0 4.3 5.0 250 265 310 400 425 485 V/VT/ VTA-903 4.0 4.3 5.0 250 265 310 400 425 485