Cummins — 3666003

Air Intake System - Overview C Series Page F-30 Section F - Familiarization Air Intake System - Overview (010-999) General Information Air is pulled into the engine through an air filter. Clean air is very important to the life of the engine; dust and dirt can damage the cylinders very quickly. Make sure that a high-quality air cleaner is used and that it is periodically replaced according to the manufacturer's recommendations. Intake air for the naturally-aspirated engine flows through the air cleaner into the intake manifold. From the intake manifold, the air is pulled into the cylinders and used for combustion.

After combustion, it is forced out of the cylinders and through the exhaust manifold. On turbocharged engines, the intake air is drawn through the air cleaner into the compressor side of the turbocharger, through the crossover tube, and into the intake manifold. From the intake manifold, the air is forced into the cylinders and used for combustion. On turbocharged engines, the energy from the exhaust is used to drive the turbine wheel of the turbocharger. The turbine wheel and shaft drive the compressor wheel, which forces more air into the cylinders for combustion. The additional air provided by the turbocharger allows more fuel to be injected to increase the power output of the engine.

On turbocharged, aftercooled engines, intake air from the turbocharger flows through the cooling fins of the aftercooler before entering the intake manifold. The cooled air becomes more dense and contains more oxygen; which allows more fuel to be injected, further increasing the power output from the engine. The 1991 to 1994 automotive engines use a chassis-mounted charge-air cooler, rather than an engine-mounted aftercooler, to provide cooler intake air to the engine. This improves the engine performance and reduce emissions. The charger-air cooler system uses large piping to transfer the air from the turbocharger to the charge-air cooler; then to the engine intake manifold. NOTE:

The long-term integrity of the charge-air cooling system is the responsibility of the vehicle and component manufacturers. Some turbocharged engines use a wastegate turbocharger to limit the maximum boost pressure that the turbocharger can develop. Wastegate operation is controlled by an actuator that senses intake manifold pressure and balances it against a preset spring-load. The wastegate valve is located in the turbine inlet passage. When open, it diverts a portion of the exhaust gas around the turbine wheel, thereby controlling the shaft speed and boost. CAUTION The turbocharger is a performance part and must not be tampered with.

The wastegate bracket is an integral part of the turbocharger. Tampering with the wastegate components can reduce durability by increasing cylinder pressure and thermal loading because of incorrect inlet and exhaust manifold pressure. Poor fuel economy and failure to meet regulatory emissions laws can result. Increasing the turbocharger boost will not increase engine power. The turbine wheel, compressor wheel, and shaft are supported by two rotating bearings in the bearing housing. Passages within the bearing housing direct filtered, pressurized engine oil to the shaft bearings and thrust bearing. The oil is used to lubricate and cool the rotating components to provide for smooth operation.

The oil then drains from the bearing housing to the engine sump through the oil drain line. A restricted or damaged oil drain line can cause the turbocharger bearing housing to be pressurized, causing oil to leak past the seals. NOTE: An adequate supply of good filtered oil is very important to the life of the turbocharger. Make sure that a high- quality oil is used and that the oil and oil filter are changed according to the maintenance recommendations. CAUTION A catalyst is installed on all EPA- and CARB-approved automotive applications. Lubricating oil blending is not permitted. It will plug up and eventually damage the catalyst. High-sulfur fuels must not be used with the catalyst.

No welding or modifications of the catalyst are permitted without permission of the catalyst manufacturer. Theory of Operation White smoke indicates cold combustion/cold engine operation. The intake manifold heater control module monitors the intake air temperature, engine rpm and keyswitch voltage. The intake manifold heater elements operate in the preheat, post heat, and post heat recycle modes. In preheat, the ignition switch is in the RUN position but the engine has not been started. In post heat and post heat recycle, the engine is operating.