Fendt 900 Vario COM III — 15 Calibration code 4007 (transmission ratio characteristic)

I003578 Fig. 168. I000557 Fig. 169. 1. The A050 basic control unit is not released immediately when the ignition is switched off. Approx. 15 seconds will lapse from the ignition being switched off to the release of the A050 2. Check connectors to the A009 actuator unit. A009 actuator unit does not actuate the precise setpoint value. Check that the transmission control runs smoothly, e.g. engage and check emergency opera- tion. F 4 Transmission ratio adjustment not effected within 8 sec. Check that the transmission control runs smoothly, e.g. engage and check emergency opera- tion. F 7 Step 2:

neutral points of transmission control for forward and reverse movement are too far apart, greater than 8°. Check A009 actuator unit to actuator shaft connection. F 8 Step 3: max. transmission ratio forward point not found. Min. setpoint value 155°, max. 187°. Step 4: max. transmission ratio reverse point not found. Min. setpoint value 136°, max. 165°. Check A009 actuator unit to actuator shaft connection. Step 3: forward actuator shaft adjustment greater than 155°, but transmission adjustment reacts less than 155°. Step 4: reverse actuator shaft adjustment greater than 135°, but transmission adjustment reacts less than 135°. Check A009 actuator unit to actuator shaft connection.

Actuator unit. F 5 Step 1: A009 actuator unit does not find neutral point 0 in forwards direction. Step 2: A009 actuator unit does not find neutral point 0 in reverse direction. Check A009 actuator unit to actuator shaft connection. 919 .. 0101-1000 925 .. 1001- 934 .. 0101-1000 919 .. 1001- 928 .. 0101-1000 934 .. 1001- 922 .. 0101-1000 928 .. 1001- 922 .. 1001- 931 .. 0101-1000 925 .. 0101-1000 931 .. 1001- Preliminary conditions not satisfied O.K. appears F 6 See error message F 5 0000 - Overall system/tractor 286 T000399 Version 3 21-04-2009 F 9 F - Setting and calibrating Fault code Cause F 1 Preliminary conditions not satisfied F 2 1.

The A050 basic control unit is not released immediately when the ignition is switched off. Approx. 15 seconds will lapse from the ignition being switched off to the release of the A050 basic control unit 2. Check connectors to the A009 actuator unit. F 3 A009 actuator unit does not actuate the precise setpoint value. Check that the transmission control runs smoothly, e.g. engage and check emergency opera- tion. F 4 Transmission ratio adjustment not effected within 8 sec. Check that the transmission control runs smoothly, e.g. engage and check emergency opera- tion. F 5 Step 1: A009 actuator unit does not find neutral point 0 in forwards direction. Step 2:

A009 actuator unit does not find neutral point 0 in reverse direction. Check A009 actuator unit to actuator shaft connection. F 6 See error message F 5 F 7 Step 2: neutral points of transmission control for forward and reverse movement are too far apart, greater than 8°. Check A009 actuator unit to actuator shaft connection. F 8 Step 3: max. transmission ratio forward point not found. Min. setpoint value 155°, max. 187°. Step 4: max. transmission ratio reverse point not found. Min. setpoint value 136°, max. 165°. Check A009 actuator unit to actuator shaft connection. F 9 Step 3: forward actuator shaft adjustment greater than 155°, but transmission adjustment reacts less than 155°. Step 4:

reverse actuator shaft adjustment greater than 135°, but transmission adjustment reacts less than 135°. Check A009 actuator unit to actuator shaft connection. Actuator unit.