DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika § Sticking or taping of washers, moving and leveling of foundation wedges. In case of grinding of the concrete by the electric grinder it is necessary to put on the cover of grinding wheel with the device for exhaustion of dust. označenн § Nalepenн nebo zaklepбnн podložek, zavezenн a vyrovnбnн zбkladovэch klнnů. V přнpadě broušenн betonu elektrickou bruskou je nutno nasadit kryt brou sнcнho kotouče se zařнzenнm pro odsбvбnн prachu. § Přivařenн konzol pro uloženн těles ventilů ke svislэm deskбm zabudovanэm v betonovйm zбkladu.

3) Instalace kozlнků a kotevnнch šroubů § Welding of the consoles for placing of valve bodies to the vertical plates which are embedded in concrete foundation. 3) Installation of pedestals and foundation bolts in the platform next the transverse wall of the opening in the top foundation slab, erection of a support deck under the hole for putting on of max. 8 pcs bolts with weight of 21,5 kg each approx. 1 m under the surface of the foundation slab, assembly of the side-support (railing) from the tube-scaffolding approx.

1 m above the foundation slab on § Preparation of foundation bolts (wrapping of bolts by the insulation tape DENSO) § Placing of the anchor bolts of pedestal of HP front and rear bearing stand on the support deck into vertical position by means of a crane, fastening of the bolts to a side-support with setting of pitches, hanging of the pedestal on a crane, moving the pedestal above the bolts and down to get the bolts through, assembly of nuts, lifting of the pedestal with hung bolts and placing of pedestal on the supporting wedges with getting the anchor bolts through the top foundation slab. § Installation of 4 x 4 anchor bolts of LP casing to top foundation slab (max.

21,5 kg each bolt) § Gradual moving of the pedestal of front and rear HP bearing stand, transverse pedestals of the bottom part of LP outer casing by the same procedure. Notice: Before moving of the pedestals of LP casing it is necessary to remove the footbridge § Ъprava plošiny v mнstě NT tělesa : vyztuženн plochy min. 6,6 x 1,0 m v plošině u přнčnй stěn y otvoru v hornн zбkladovй desce, vytvořenн opěrnй plošiny pod dнrou pro uloženн max. 6 ks šroubů max. 21,5 kg každэ cca 1,0 m pod ъroveň povrchu zбkladovй desky, montбž bočnн opěry (zбbradlн) z trubkovйho lešenн cca 1 m nad zбkladovou desku na obvod dнry , § Přнprava zбkladovэch šroubů (navinutн izolačnн pбsky DENSO).

§ Uloženн kotevnнch šroubů kozlнku přednнho a zadnнho VT ložiskovйho stojanu na opěrnou plošinu je řбbem do svislй polohy, uvбzбnн šroubů k bočnн m opěrбm s nastavenнm roztečн, zavěšenн kozlнku na jeřбb, najetн kozlнkem na d šrouby , navlečenн kozlнku na šrouby, montбž hornнch matic, zvednutн kozlнku se zavěšenэmi šrouby a uloženн kozlнku na připravenй klнnovй podložky s provlečenнm kotevnнch šroubů skrze hornн zбkladovou desku. § Zavezenн 4 x 4 ks zбkladovэch šroubů zadnнho NT tělesa v hornн zбkladovй desce (max. 21,5 kg každэ šroub). § Postupnй zavezenн kozlнku přednнho a zadnнho V T ložiskovйho stojanu, přнčnэch kozlнků spodku NT vnějšнho tělesa stejnэm způsobem. Poznбmka:

Před zavezenнm kozlнků NT tělesa je nutno odstranit pochozн lбvku Date: 12.11.2013 Page 103 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ § Creating of workplace for welding including measures O&S, FP, EP equal to welding on the top concrete slab of foundation stool. § Vytvoření pracoviště pro svařování včetně opatření BOZP,PO,OŽP přiměřených pro svařování na horní betonové desce základové stolice. § Modification of the platform in place of LP casing : reinforcement of area min. 6,6 x 1,0 m položení pochozí lávky přes otvor v horní základové desce podél díry, bezpečnostní označení pracoviště.

circumference of the hole, putting of footbridge over the opening along the hole, safety marking of the workplace.