DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika § Dokončenн nбtěrů v mнstě svarů a oprava nбtěrů poškozenэch montбžnн činnostн, nanesenн lokбlnн konzervace bude -li potřeba. § Montбž tepelnэch izolacн na tělesa turbiny a ventilů s ohledem na provedenн VPN před najetнm. § Předmontбž protihlukovйho krytu § Přнprava turbiny na provoz na natбčedle a k provedenн individuбlnнch zkoušek na souvisejнcнch zařнzenнch 20) Korekce vyrovnбnн parnн průtočnй čбsti § Completion of paints in places of welds and repair of the paints which were damaged during assembly works, application of local preservation if necessary.

§ Assembly of thermal insulation on turbine casings and valves bodies with respect to measuring of VPN before start up.

§ Pre-assembly of anti-noise cover § Preparation of turbine for operation on turning gear and for carry out of individual tests on related devices 20) Correction of concentricity setting in the turbine steam flow path and rotorsґ catenary connecting in couplings befor ethe first start up § Open of bearing stands and releasing of rotors in coupling § Filing of condensers up to operation level, unlock the spring support of condensers and cooling water piping § Carrying out of measurement by very precise leveling (VPL), measurement of rotor-set alignment in couplings, measuring of the casings position against rotors § Evaluation of measurements and carrying out of alignment (bearings inside of bearing stands, LP inner casing in outer, installation of final pads of inner casing instead of adjustable pads) § Rotor’s system coupling together, closing of bearing stands § Finishing of thermal insulation assembly § Preparation of turbine for preheating and staring up on the speed § Introduction of measures of OHS, FP, EP on workplace for turbine washing after assembly.

§ Check of the safety sheets of washing means turbiny a sespojkovбnн rotorovй soustavy před prvnнm najetнm § Otevřenн ložiskovэch stojanů a uvolněnн rotor ů ve spojkбch § Naplněnн kondenzбtoru na provoznн hladiny, uvolněnн pružinovэch podpěr kondenzбtoru , potrubн chladнcн vody a hornн zбkladovй desky (existujн -li) § Provedenн měřenн velmi přesnou nivelacн (VPN), měřenн vyrovnбnн rotorovй soustavy ve spojkбch, měřenн polohy těles vůči rotorům.

§ Vyhodnocenн měřenн a provedenн ъprav vyrovnбnн (ložiska uvnitř ložiskovэch stojanů, N T vnitřnн těleso ve vnějšнm, instalace fi nбlnнch podložek vnitřnнch těles namнsto stavitelnэch podložek) § Sespojkovбnн rotorovй soustavy, zavřenн ložiskovэch stojanů § Dokončenн montбže tepelnй izolace § Přнprava turbiny k prohřevu a najetн na otбčky § Umytн turbiny a protihlukovйho krytu § Demontбž vnějšнho lešenн a vyklizenн § Washing of turbine and anti-noise cover § Dismantling of outer scaffolding and cleaning Date: 12.11.2013 Page 113 / 278 Prepared: O.Baroch Last Revision: Approved:

P.Lešetickэ § Application of measures for work with paints from point of view of OHS, FP, EP, checking of the safety sheets of the paints § Zavedení opatření pro práci s nátěrovými hmotami z hlediska BOZP, PO, OŽP, kontrola bezpečnostních listů nátěrových hmot. § Preparation of workplace for assembly of thermal insulation (adjustment of the platforms and scaffoldings) § Adaptation of measures of OHS, FP, EP adequate for work with thermal insulation § Příprava pracoviště pro montáž tepelných izolací (úprava lešení a plošin). § Úprava opatření BOZP, PO, Ekologie přiměřeně pro práci s tepelnou izolací.

§ Zavedení opatření BOZP, PO a Ekologie na pracovišti za účelem mytí turbiny po provedené montáži. § Kontrola bezpečnostních listů mycích prostředků