DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika platform in place of LP casing: reinforcement of area min. 6,6 x 1,0 m in the platform next the side wall of the opening in the top foundation slab, erection of a support deck under the hole for putting on of max. 6 pcs bolts with weight of 21,5 kg each approx. 1 m under the surface of the foundation slab, assembly of the side-support (railing) from the tube-scaffolding approx. 1 m above the foundation slab on circumference of the hole, putting of footbridge over the opening along the hole, safety marking of the workplace.

· Hang the pedestals on crane, put it on arranged anchor bolts, mount the upper washers and screw up the nuts on theraded boltsґ ends up to distance according to drawing. Screw up the anchor bolts in the axis of turbine rotors (total 8 pcs) in cross-sections B-B, C-C straight into the threaded holes in pedestals. · Lift always the pedestal with the hung bolts and move it on position with getting the anchor bolts through the top foundation slab of concrete stool. · Lift the bolts from bottom, assemble the washers and nuts and hang the bolts on the pedestal of rear IP bearing stand according to cross-section B-B, C-C in Tp6075643.

Lift the pedestal by a crane, move it aside, remove all provisory supports, clean properly the holes from dust & free corpuscles and put the pedestal on position. If an imbalance (big length-difference of bolts on the pedestal) causes a difficulties with levelling, assemble an equal counter-weight on the pedestal. Notices: Weight of anchor bolt is max. 21,5 kg. During putting of anchor bolts through the foundation slab be careful and avoid a damage of the thread’s ends. Attention: Never enter or put your limbs directly under the hung pedestal!! · Carry out the assembly of the lower foundation plates and nuts.

· Check the height position of the anchor bolts according to drawing Anchor bolts no. Tp6075643 and correct it if necessary. · Set the position of the pedestals of bearing stands in horizontal plane acc. to the gauge lines on the concrete foundation slab. Carry out the following arrangement of the tělesa: vyztuženн plochy min. 6,6m x 1 m v plošině u bočnн stěny o tvoru v hornн zбkladovй desce, vytvořenн opěrnй plošiny pod dнrou pro uloženн max. 6 ks šroubů max.

21, 5 kg každэ cca 1,0 m pod ъroveň povrchu zбkladovй desky, montбž bočnн opěry (zбbradlн) z trubkovйho lešenн cca 1 m nad zбkladovou desku na obvod dнry, položenн pochozн lбvky přes otvor v hornн zбkladovй desce podйl dнry, bezpečnostnн označenн pracoviště. · Kozlнk y zavěšte na jeřбb, navlečte jej na připravenй zбkladovй šrouby, montujte hornн podložky a našroubujte matice na zбvitovй konce šroubů do vэkresovй vzdбlenosti. Kotevnн šrouby v ose rotorů turbiny (celkem 8 ks) v řezech B-B, C-C zašroubuj te přнmo do zбvitovэch děr kozlнků . · Zvedněte vždy kozlнk se zavěšenэmi šrouby jeřбbem a zavezte jej na pozici s provlečenнm zбkladovэch šroubů skrze hornн zбkladovou desku betonovй stolice.

· Zvedněte zespoda, montujte podložky a matice a zavěšte šrouby na kozlнk zadnнho VT ložiskovйho stojanu a kozlнku přednнho S T ložiskovйho stojanu dle řezu B-B, C-C na Tp6075643 . Zvedněte kozlнk jeřбbem, odvezte jej stranou, odstraňte provizornн podpěrnй podložky, vyčistěte důkladně dнry od prachu & volnэch čбstic a uložte kozlнk na pozici. V přнpadě, že nevэvažek ( velkэ rozdнl dйlky šroubů na kozlнku) způsobн potнže, montujte na kozlнk odpovнdajнcн protizбvažн. Poznбmk y: Max hmotnost zбkladovйho šroubu je 21,5 kg. Při provlйkбnн zбkladovэch šroubů skrze zбklad dejte pozor, aby nedošlo k poškozenн zбvitovэch konců. Upoz orněnн:

Nikdy nevstupujte a nedбvejte končetiny přнmo pod zavěšenэ kozlнk!! · Proveďte montбž spodnнch zбkladovэch desek a matic. · Kontrolujte a přнpadně nastavte sprбvnou vэškovou polohu kotevnнch šroubů dle vэkresu Šrouby zбkladovй sestavenн “ č. Tp6075643. · Ustavte kozlнky ložiskovэ ch stojan ů v horizontбlnн rovině dle orэsovбnн betonovй zбkladovй desky. P roveďte nбsledujнcн přнpravu kozlнků : Date: 12.11.2013 Page 126 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ