DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika values from the preassembly which was carried out in DSPW written in Turbine Dozier book. b) If the preassembly has not been done in DSPW, set the pedestal position according to HP bearing distance 4835 mm (after opening bearing’s stands and bearings) symmetrically from lateral axis of the LP casing by means of the measuring tape, the distance between guiding feathers of the front HP and of the rear HP pedestals should be 3895 mm.

· After setting of the axial position of the front bearing stand fix the position of the stand by tightening of the side splices to the pedestals by means of the bolts M36x3 pos.15 ( Tp6076030 ). Put the inserts made from non- asbestos (or similar material) sealing plates (thickness 1 mm ) on the upper surface under the splices of longitudinal guidance of stand just before bolts tightening. It will fix the bearing stand to the pedestal for further assembly.

Seal the parting planes between pedestals and stands against penetration of dust (waterproof tape Duck Tape 3939) · After setting of the axial position of IP rear bearing stand and LP rear bearing stand fix the position of the stands by means of the tightening of bolts pos.13 (M36) see drawing Tp6074949 . Attention: It is necessary to set the position of the bearing stand on the pedestals with taking respect to operating shift of stand (oil pipes outlet). Basic side setting of the bearing’s stands: · Install the string into the longitudinal axis of turbo-set.

Rough side setting of the bearing’s stands on string (longitudinal axis of steam turbine casing and generator), take out the string after setting of all stands. Set the mutual camber-elevation of the bearings, stands slopes and make more accurate the side position of bearing’s stands: Note: The activities described below do not until the final setting of the LP outer casing is done. · For rotors’ alignment of turbine for 210 MW BANDEL is chosen this logic: bearings of LP provedenй v DSPW – uvedeno v Pasportu Turbiny.

b) V p řнpadě, že kontrolnн montбž v DS PW neproběhla, naměřte polohu kozlнků pбsmem dle VT ložiskovй vzdбlenosti 4385 mm, souměrně od přнčnй osy V T tělesa (po otevřenн ložiskovэch stojanů a ložisek), vzdбlenost mezi vodнcнmi pery zadnн časti přednнho VT a přednн čбsti zadnнho VT kozlнků by měla bэt 3895 mm . · Po axiбlnнm ustavenн přednнho ložiskovй ho stojanu, zafixujte jeho polohu utaženнm stranovэch přнložek podйlnйho vedenн stojan u ke kozlнk u pomocн šroubů M36x3 poz.15 ( Tp6076030 ). Před utaženнm šroubů vložte na hornн plochu vedenн ložiskovйho stojanu, pod přнložky cca 1 mm silnэ pбsek z bez- asbestovй těsnнcн desky , nebo podobnйh o materiбlu.

Tнmto se pevně zafixuje ložiskovэ stojan ke kozlнku pro dalšн montбž. Zatěsněte dělнсн rovin u mezi kozlнk em a stojanem proti vniku prachu (vodě odolnб pбska - Duct Tape 3939) · Po axiбlnн m ustavenн polohy zadnнho VT ložiskovйho stojanu zafixujte jeho polohu utaženн m šroubů poz.13 (M36) na vэkre se Tp6074949 . Upozorněnн: Polohu ložiskovйho stojanu na kozlнku je nutno ustavit s ohledem na provoznн posuvy stojanu (roury odpadu oleje). Proveďte zбkladnн stranovй ustavenн ložiskovэch stojanů: · Instalujte strunu do podйlnй osy turbosoustrojн. Ustavte hrubě stranově ložiskovй stojany turbiny na strunu (podйlnб osa těles parnн turbiny s generбtorem), po ustavenн všech stojanů strunu sejmout.

Nastavte vzбjemnй převэšenн ložisek, sklony stojanů a upřesněte stranovй ustavenн ložiskovэch stojanů: Poznбmka: Nнže popsanй činnosti provбdějte až po fi nбlnнm ustavenн spodku NT vnějšнho tělesa. · Pro turbinu 210 MW BANDEL je zvolena tato logika vyrovnбnн rotorovй soustavy: ložiska NT Date: 12.11.2013 Page 134 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ