DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika · Otevřete vнka ložiskovэch stojanů, otevřete ložiska a smyjte konzervaci z ložisek, distančnнch podložek, klнnů a ložiskovэch stojanů v mнstě uloženн ložisek. Pozor na vzбjemnй seznačenн polovin klнnu ve dvojici - dosedacн plocha ložiska! Pokud nenн nutnй, neměňte vzбjemnou polohu klнnů ve dvojici - již nastaveno z kontrolnн montбže u vэrobce. · Distančnн podložky (kameny) axiбlnнho segmentovйho ložiska ponechte namontovanй na ložisku! – jsou již přesně nalнcovбny z kontrolnн montбže u vэrobce.

Proveďte kontrolu stavu ložisek po transportu za ъčasti pracovnнka Jakosti DSPW. Proměřenн geometrie ložiskovэch pбnvн nenн nutno provбdět – měřenн provбdějte pouze na požadavek odběratele nebo v oddůvodněnэch přнpadech. Proveďte zбpis o kontrole ložisek d o Montбžnнho denнku. Set the axial position of the LP rear bearing and the LP front bearing this way: a) If the preassembly has not been done in · Open the covers of bearing’s stands open the bearings and wash off the preservation from bearings, stones, wedges, and stands on surface of contact with bearings. Pay attention to the marking of mutual position of both wedges in couple and the contact surface of bearing!

If it is not necessary, don’t change the mutual position of wedges in pairs it was already set during preassembly in producing plant. · Leave the space-washers (stones) of the thrust segment bearing assembled on the bearing! They are precisely fitted from preassembly by producer. Check the condition of bearings after transport with participation of DSPW Quality assurance person. It is not necessary to carry out the measurement of geometry of bearing shells do it just on request of purchaser or in a reasonable case. Carry out a record to Log book about the check of bearings. Nastavte axiбlnн polohu zadnнho NT ložiska a přednнho NT ložiska takto:

a) V přнpadě, že kontrolnн montбž v DSPW neproběhla, naměřte polohu kozlнků pбsmem dle NT ložiskovй vzdбlenosti 5030 mm , souměrně od přнčnй osy NT tělesa (po otevřenн ložiskovэch stojanů a ložisek ). Nastavte a xiбlnн polohu přednнho NT ložiska a zadnнho V T kozlнku s kombinovanэm ložiskovэm stojanem takto: a) Nastavte vzdбlenost ložiskovэch stojanů pбsmem, dle hodnot z kontrolnн montбže provedenй v DSPW uvedeno v Pasportu Turbiny. b) V přнpadě, že kontrolnн montбž v DSPW neproběhla, naměřte polohu kozlнků pбsmem dle VT ložiskovй vzdбlenosti 4760 souměrně od přнčnй osy NT tělesa (po otevřenн ložiskovэch stojanů a ložisek ) .

Nastavte a xiбlnн polohu z adnнho VT kozlнku s kombinovanэm ložiskovэm stojanem a přednнho VT kozlнku s ložiskovэm stojanem takto: a) Nastavte vzdбlenost ložiskovэch stojanů pбsmem, dle hodnot z kontrolnн montбže DSPW, set the pedestal position according to LP bearing distance 5030 mm (after opening bearing’s stands and bearings) Set the axial position of the rear HP pedestal and of the front HP pedestal with combined bearing’s stands this way:

a) Set the distance between the bearing stands by means of the measuring tape according to values from the preassembly which was carried out in DSPW written in Turbine Dozier book b) If the preassembly has not been done in DSPW workshop, set the distance between pedestals as the distance between HP bearings 4760 mm (after opening of the bearing’s stands a bearings) Set the axial position of the HP rear pedestal with combined bearing stand and of the HP front pedestal with the bearing’s stands this way: a) Set the distance between the bearing stands by means of the measuring tape according to Date: 12.11.2013 Page 133 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ