Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika Prepare the Dummy shafts ( IP and LP) Tp6071233 and remove the preservation from the shafts surface and from all rings (Ш355 , Ш 400 a Ш430 mm). Check the condition of shafts and rings. Grease the surfaces of the shafts and rings a little by oil or grease paste. Prepare the shafts for putting into the bearings (slide the rings on the shafts, set the pitch at right distance of axis of bearings (IP 4760 mm, LP 5030 mm) Připravte Kontrolnн hřнdele ( ST a NT) č.v. Tp6071233 a odstraňte konzervaci z povrchu hřнdelн i všech kroužků (Ш355 , Ш 400 a Ш430 mm).
Zkontrolujte stav hřнdelн i kroužků. Povrchy hřнdelн a průměry kroužků lehce namažte olejem, nebo mazacнm tukem. Připravte hřнdele pro vloženн do ložisek (nasunout kroužky na hřнdele, nastavit rozteč na sprбvnou osovou vzdбlenost ložisek, ST - 4760 mm, NT 5030 mm). · Put the dummy shafts with rings into the bearings and measure their position against the bearing’s stands (in bore) · Set the bearings elevation and slopes of the stands: set the LP bearings and carry out their accurate leveling together with bottom of the LP casing (measuring to bore and parting plane, divide the araised deviations so that the work-consumption is minimal).
After that the other bearings elevation setting can continue. · Carry out the measuring of the elevation position of LP bearings by optic & laser leveling to the rings of the dummy shafts in bearings against the altitude refer point of machine hall. Carry out the measuring of elevation at the other bearings by optic & laser leveling or by the hose level on the rings of the dummy shafts putted into the individual bearings. · Carry out the change of the elevation and side position of the bearings and the slope of the stands by the whole pedestals (tamping of the wedges). During leveling tighten the foundation bolts continuously.
· The bearing’s stands has to be horizontal in transverse direction measure by water level. The slopes of the bearing’s stands in longitudinal direction arise after setting of the mutual camber-elevation of the bearings and in case that there are values from · Vložte kontrolnн hřнdel s kroužky do ložisek a změřte jejich polohu vůči ložiskovэm stojanům (ve vэvrtu) . · Nastavte převэšenн ložisek a nбklony stojanů: ustavte NT ložiska a jejich přesnй vyrovnбnн proveďte spolu se spodkem vnějšнho NT tělesa (měřenн na vэvrt a dělнсн rovinu, vzniklй odchylky rozdělte tak, aby pracnost operace byla minimбlnн). Potй pokračujte v nastavenн převэšenн ostatnнch ložisek.
· Měřenн vэškovй polohy ložisek NT proveďte nivelacн na kroužek kontrolnн hřнdele v ložisku vůči referenčnнmu bodu strojovny . M ěřenн převэšenн ostatnнch ložisek provбdějte nivelacн nebo hadicovou vodovбhou na kroužky kontrolnнch hřнdelн vloženэch do jednotlivэch ložisek. · Změnu vэškovй a stranovй polohy ložisek a nбklonu stojanů provбdějte vždy celэm kozlнkem (podbнjenнm klнnů). Přitom provбdějte průběžně utahovбnн zбkladovэch šroubů · Ložiskovй stojany musн stбt v přнčnйm směru vodorovně – měřte zбmečnickou vodovбhou. Sklony ložiskovэch stojanů v podйlnйm směru vyplynou po nastavenн vzбjemnйho převэšenн ložisek . V přнpadě, že existujн hodnoty z kontrolnн montбže, upřesnн se Date:
12.11.2013 Page 136 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ