Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika plane and grease the thread-ends of screws with anti-sizing compound Molykote G Rapid+. · Check the readiness of the LP bottom casing for further assembly. Inspection can be done only with presence of DSPW technical advisor for turbine assembly and DSPW Quality inspector. Print the record about inspection (included in quality documentation) . Work status: Bottom part of LP outer casing is assembled and ready for assembly of covers and inner parts.
Bottom part of deflectors are assembled (tightness welds are completed, parting planes are leveled to turbo-set axis according to Turbine Dozier book) · Proveďte kontrolu připravenosti spodku NT tělesa na dalšн montбž. Kontrola může proběhnout jen za ъčasti šйfmontйra a zбstupce pro Jakost DSPW. Vystavte zбznam o provedenн kontroly (součбst dokumentace jakosti) . Stav pracн: Spodek NT vnějšнho tělesa je smontovanэ a připravenэ pro montбž vнk a vnitřnнch dнlů , spodnн čбst deflektorů je smnontovбna (těsnostnн svary jsou dokončeny, dělнсн roviny vyrovnбny na osu stroje dle pasportu turbiny).
Pre-assembly of deflectors of LP middle casing · Prepare the parts of deflector (N-Tp6069380) of LP inner casing for assembly i.e. preservation washing, check the condition, clean the holes for centering pins in deflector’s parting planes, clean and grease the bolts and pins for deflectors attaching to LP inner casing with the paste Molykote G Rapid + . · Pre-assemble the parts of deflectors (the quarters) by means the screws pos. 13 to get the bottom and upper halves according to mutual marking. Nuts pos.14 tighten lightly and after centering knock in the conical pins pos. 8 . and cylindrical pins pos.15 . Then insert the bolts pos. 6 and tighten the nuts pos. 7 .
Final tightening of screws of deflectors will be carry out after final assembly of LP inner casing (deflectors used to be usually partly assembled and transported as the halves with partly assembled piping of cooling water into steam see photo). · Move the bottom halves of deflectors into LP outer casing and hang them on provisory pins poz. 50 cross-section K-K in drawing Tp6040130 which are placed on the rear and front parts of the bottom part of LP outer casing. The holes in cross section C-C in the drawing of deflector Tp6037561 serve for hanging of the bottom half of deflector on the pins of transverse wall. · Připravte dнly deflektorů (N -Tp6069380) NT vnitřnнho tělesa na montбž, tj.
mytн konzervace, kontrola stavu, čistěnн otvorů pro středнcн kolнky v dělнcнch rovinбch deflektorů, čištěnн a mazбnн šroubů a kolнků pro upevněnн deflektorů k vnitřnнmu NT tě lesu pastou Molykote G Rapid + . · Předmontujte dнly (čtvrtiny) deflektorů pomocн šroubů poz. 13 do spodnнch a hornнch polovin dle seznačenн. Matice poz.14 lehce dotбhněte a po vystředěnн naklepněte kuželovй kolнky poz.8 . a vбlcovй kolнky poz. 15 . Potй vložte šrouby poz.6 a utahujte matice poz.7 .
Ъplnй dotaženн šroubů deflektorů bude provedeno až po celkovйm sestavenн obou polovin vnitřnнho NT tělesa (deflektory bэvajн však pro dopravu již čбstečně smontovбny a dopraveny jako poloviny i s čбstečně namontovanэm potrubнm vodnнho chlazenн pбry – viz foto). · Zavezte spodnн poloviny deflektorů do vnějšнho NT tělesa a zavěste je na montбžnн čepy poz. 50 řez K-K na vэkrese Tp6040130 umнstěnэch na přednн a zadnн čбst vnějšнho tělesa. K zavěšenн poloviny deflektoru na čepy přнčnй stěny sloužн otvory dle řezu C-C na vэkrese deflektoru Tp6037561 . Před - montбž deflektorů střednнho NT tělesa Date: 12.11.2013 Page 146 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ