Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika Measuring of the stator parts position in LP Naměřenн polohy statorovэch dнlů NT steam flow path and radial position setting: Attention: All below described measurements till LP casing’s boxing up can be done exclusively with presence of DSPW Technical Advisors or DSPW Quality inspector. For the setting of rough radial position of mentioned parts, there has to be available LP bearings, LP rotor and the dummy shaft for LP part.
HP and IP turbine casing should be already placed o n bearing’s stands; if HP and IP part delivery is not available yet it is possible to continue with assembly work with the awareness, that it will be necessary repeat some measurement and assembly operations (HP and IP part weight influence). · Put in the LP dummy shaft with rings into the bearings and take up the clearances among the bottom parts of casings and the temporary set-wedges. průtočnй čбsti a radiбlnн vyrovnбnн : Upozorněnн: V eškerб nнže popsanб měřenн až do okamžiku zavřenн NT těles a je nutno provбdět vэhradně za přнtomnosti šйfmontйra nebo kontrolora DSPW.
Pro hrubй radiбlnн ustavenн dнlů NT průtočnй čбsti musн bэt k dispozici NT ložiska, NT rotor a kontrolnн hřнdel pro NT čбst. VT a ST dнl turbiny by měl bэt již uložen na ložiskovэch stojanech; nenн -li VT a ST dнl dosud dodбn je možno pokračovat s montбžн s vědomнm, že bude nut no některб měřenн a montбžnн operace opakovat (vliv hmotnosti VT a ST dнlu) · Vložte NT kontrolnн hřнdel s kroužky do ložisek a proveďte vymezenн vůle mezi spodky těles a montбžnнmi stavěcнmi klнny.
· Measure the radial position of bottom part of LP inner casing against the bores of bottom parts of LP diaphragms in grooves for labyrinth segments of the shaft glands and on surfaces next to the honey-comb sealing of circumference of blades of moving wheels (before measuring the labyrinth segments have to be taken out from the gland bodies and from shaft glands of diaphragms). Notice: It is not necessary to perform the check- measurement of bore shape of inner components of LP steam flow path. If it is required by purchaser or there are reasons for measuring, carry out it as following:
gradually put the upper halves of inner parts onto · Naměřte radiбlnн polohu spodku NT vnitřnнho tělesa podle vэvrtů spodků NT rozvбděcнch kol v drбžkбch pro hřнdelovй ucpбvky a na plochбch vedle voštinovйho těsněnн obvodu lopatkovбnн oběžnэch kol (před měřenнm musн bэt vyjmuty labyrintovй segmenty z těles ucpбvek a hřнdelovэch ucpбvek rozvбděcнch kol). Poznбmka: Kontrolnн měřenн tvaru vrtбnн vnitřnнch dнlů NT průtočnй čбsti nenн potřeba provбdět. Požaduje - li jej zбkaznнk nebo jsou -li pro měřenн důvody, proveďte jej takto: postupně poklбdejte hornн poloviny vnitřnнch dнlů na spodky, kontrolujte kontakt v dělнсн rovině a Date: 12.11.2013 Page 155 / 278 Prepared: O.Baroch Last Revision:
Approved: P.Lešetickэ