Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika - During casing boxing up measure the - Během zavнrбnн těles proměřujte spбroměrkou dosedбnн dělнcнc h rovin NT těles a ve volnйm stavu před utaženнm šroubů. - Proveďte měřenн L -P-D-H hodnot po zavřenн NT vnějšнho tělesa; toto měřenн se provбdн opakovaně a je platnй pouze v přнpadě, pokud vэsledky po sobě jdoucнch měřenн se nelišн o vнc než 0,1mm. - Sejmutн krytek nivelačnнch čepů na vnějšнm NT tělese a na ložiskovэch stojanech, měřenн vzбjemnй polohy nivelačnнch bodů metodou „Velmi přesnй nivelace (VPN)“:
měřenн vzбjemnй polohy nivelačnн čepy vnějšнm NT tělese - ložiskovй stojany a ložiskovй čepy NT rotoru. - Demontбž hornнch dнlů až do otevřenн NT proper contact of parting planes of LP casing by feeler gauge in free state just before bolts tightening. - Carrying out the measurement of values L- R-B-T after LP casing boxing up; this measurement is carried out repeatedly and it is valid only if the results of consecutive measurements do not differ more then 0,1mm. - Taking out the caps of leveling pins on outer LP casing and on bearing’s s tands; mutual position measuring of the leveling pins by “Very Precise Leveling” (VPL):
mutual position measuring of leveling pins on outer LP casing bearing’s stands and journals of LP rotor. - Dismantling of the top parts up to opening of LP casing in parting plane - VPL measuring in open state with rotor tělesa do dělнсн roviny - Měřenн VPN v otevřenйm stavu s rotorem inside. - Taking out the rotor, dismantling of EPRO uvnitř. - Vyjmutн rotoru, demontбž snнmačů EPRO. sensors - Evaluation of measured values, compare - Vyhodnocenн naměřenэch hodnot, porovnejte vэsledky s hodnotami v pasportu turbiny. Vэsledky se nesmн lišit o vнce než 0,2 mm, v opačnйm přнpadě je nutnй provйst korekce polohy vnitřnнch dнlů a měřenн VPN opakovat.
v Ověřenн sprбvnйho ustavenн centricity pomocн nбplastн takto (včetně přнpravnэch pracн): - Montujte labyrintovй segmenty do ucpбvek - Nalepte nбplasti nahoru na rotor do mнst s nejmenšн vэkresovou vůlн (obvod vůle mezi rotorem a rozvбděcнm kolem) a vložte rotor do ložisek. - Namontujte hornн poloviny rozvбděcнch kol, vložte olověnэ drбt, pro zjištěnн dilatačnнch vůlн vůči vнku NT tělesa. - Proveďte zavřenн NT vnějšнho tělesa results with values in Turbine Dozier book. Results must not differ more then 0,2 mm, otherwise it is necessary to correct the position of inner parts and repeat VPL measuring.
v Verify the right setting of stator parts concentrity by means of plasters as following (including preparation works): - Assemble labyrinth segments into glands - Stick the plasters on top of rotor in places with smallest clearance in accordance of drawing (circumference clearance between rotor and diaphragm) and put rotor into bearings. - Assemble the upper halves of diaphragms, put on a lead wire for measuring of the dilatation clearances against the top of LP casing - Box up of LP outer casing including 100% tightening bolts. - Measure the “top gaps” between blades of včetně 100% utaženн šroubů. - Odměřte „špičkovй vůle“ mezi oběžnэmi moving wheel and diaphragms 3-3a.
Nominal clearance of LP casing has to be approx 18.4 mm ( Tp6072423 ) in cold-state; accurate values of clearances are recorded in Turbine Dozier book. lopatkami 3-3a a rozvбděcнmi koly. U NT tělesa musн bэt ve studenйm stavu jmenovitб vůle cca 18,4 mm ( Tp6072423 ) přesnй hodnoty vůlн jsou zaznamenбny v pasportu turbiny. Date: 12.11.2013 Page 160 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ