Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika provided by DSPW staff in such case. zajistili pracovnнci DSPW . More details about the concentrity measurement in closed state and checking of the right position setting by means of the plasters described below: v Installation of contactless sensors EPRO Detailněji jsou činnosti při měřenн centricity v zavřenйm stavu a kontrole sprбvnйho vyrovnбnн pomocн nбplastн popsбny nнže:
v Instalace bezdotykovэch snнmačů EPRO on LP rotor and preparation for concentrity measuring of the stator elements against rotor - Mark the axis for sensors attachment (on na NT rotor a přнprav a na měřenн centricity statorovэch dнlů vůči rotoru - Vyznačenн os pro upevněnн snнmačů na rotor sides in the height of parting plane) - Attaching the holders with EPRO sensors NT rotor (z boků rotoru ve vэšce dělнсн roviny) - Upevněnн držбкů se snнmači EPRO na rotor opбsбnнm plastovou pбskou napнnanou stahovacн kabelovou pбskou. - Upevněnн sdružovacн skřнňky s převodnнky to LP rotor by stratch harnessing with plastic tape and by cable pulling tape.
- Attaching of the junction box with signal transmitters onto rotor in the place between glands and oil insert - Assembly of cables (cables from sensors signбlu na rotor v mнstě mezi ucpбvkou a olejovou vložkou - Montбž kabelů (kabely od snнmačů připojeny do sdružovacн skřнňky a odtud jedinэ kabel vyveden do měřнсн ъstředny vně tělesa turbiny) a upevněnн kabelů na rotor lepнcн pбskou. - Poznбmka: Labyrintovй segmenty musн are connected to junction box and just one cable is outlet to the measure-cubicle placed out of turbine casing) and attachment of cables to the rotor by an adhesive tape. - Notice: Labyrinth segments are taken out from shaft glands in diapragms and outer LP gland bodies.
- Marking of sensors position on coupling bэt vyjmuty z hřнdelovэch ucpбvek rozvбděcнch kol a z vn ějšнch NT ucpбvek . - Vyznačenн polohy snнmačů na spojkovйm hubs. - Putting LP rotor into the casing with sensor kotouči. - Vloženн NT rotoru do tělesa snнmači vzhůru, zapojenн a odzkoušenн měřenн s otбčenнm rotoru (měřн se Levб – Pravб – Dolnн – Hornн). v Měřenн korekcн pro ustavenн centricity on the top, connecting and testing of measuring with rotor turning (measure Left Right Bottom Top). v Measuring of corrections for setting the concentrity in closed state against the rotor. - LP casing boxing up: Gradual assembly of v zavřenйm stavu na rotor - Zavřenн NT tělesa:
Postupnб montбž hornнch polovin vnitřnнch dнlů, utahovбnн šroubů jejich dělнcнch rovin na dosednutн a měřenн L -P-D- H hodnot. Průběžně měřte změnu polohy statorovэch dнlů vůči rotoru při zatěžovбnн a stahovбnн dělнcнch rovin. P růběžně měřte změny špičkovэch vůlн. - Během zavнrбnн těles proměřujte odpichem změny polohy statorovэch dнlů vůči rotoru na přнstupnэch mнstech (vэvrty stojanů a těles, drбžky rozvбděcнch kol). halves of upper inner parts, tightening of screws in parting planes up to proper contact and measuring of values in L P B T. During rotor loading and tightening of parting planes continuously measure change of the position of stator parts against rotor.
Continuously measure the changes of top gaps. - During casing boxing up measure the stator parts position against rotor in accessible places (bores of stands and casings, grooves of diaphragms) by the inside micrometer. Date: 12.11.2013 Page 159 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ