DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika DSPW production plant: For the compact object of measurement there is considered a set of: bearing stands rotor bearing journals turbine casings.

There will be actually carried out a record of the mutual positions of leveling points on mentioned components, after a right setting of stator components centricity against the rotor in closed state of the turbine casings (the parting planes are in full contact) and in open state of the internal parts in the steam flow path (upper parts of casings are taken out), and at the end it is done a record of leveling points position when the dummy shaft is inserted inside the turbine casing (against the shaft rings putted into the bearings). The right setting of centricity is the result of other applied methods, which are not included in this manual.

In those states there are also recorded the measurements by means of the inside micrometer against the dummy shaft (dummy shaft bores of circular recesses in bearing stands bores of grooves in diaphragms) and against the rotor (turbine rotor bores at bearing stands, clearances between the rotor last blades and stator, so called peak clearance). Aim of VPL measurement at this stage is to get benchmarks for the assembly of Steam Turbine at site. Measurement is carried out during the preassembly directly at SPW producing plant. B) Measurement before final boxing up of the Steam Turbine casings: For the compact object of measurement there is considered a set of:

bearing stands rotor bearing journals leveling pegs at turbine bodies leveling pegs at concrete foundation. The aim is to obtain data for checking and doing of contingent correction of: - the right setting of the steam flow path centricity - the elevation of the rotor bearing journals before coupling connection - the mutual position of all the leveling points before the piping connecting to bottom of the turbine casing and before TG commissioning C) Measurement after completion of assembly just before the reaming of holes for coupling bolts and before the coupling connection: For the compact object of measurement zбvodě DSPW: Za kompaktnн objekt měřenн je zde uvažovбna soustava:

ložiskovй stojany - ložiskovй čepy rotoru – tělesa turbiny. Provede se vlastně zбznam vzбjemnй polohy nivelačnнch bodů na uvedenэch dнlech po sprбvnйm ustavenн centricity statorovэch dнlů vůči rotoru a to v zavřenйm stavu těles (dělнсн roviny v plnйm kontaktu) a v otevřenйm stavu vnitřnнch dнlů průtočnй čбsti (hornн dнly těles jsou sejmuty) a nakonec se provede zбznam polohy nivelačnнch bodů při kontrolnнm hřнdeli vloženйm do tělesa turbiny (na kroužky hřнdele vloženэch do ložisek). Sprбvnй ustavenн centricity je vэsledkem dalšнch aplikovanэch metod, kterй nejsou uvedeny v tomto manuбlu.

V uvedenэch stavech jsou ro vněž provedeny zбznamy měřenн mikrometrickэm odpichem na kontrolnн hřнdel (kontrolnн hřнdel – vrtбnн vэkružků ložiskovэch stojanů – vrtбnн drбžek rozvбděcнch kol) a na rotor (rotor vэkružky ložiskovэch stojanů, lopatkovбnн největšнch kol tj. špičkovб vůl e lopatek). Cнlem měřenн VPN v tйto fбzi je stanovenн referenčnнch hodnot pro montбž parnн turbiny na staveništi. Měřenн se provбdн při kontrolnн montбži přнmo ve vэrobnнm zбvodě DSPW. B) Měřenн před finбlnнm uzavřenнm těles Parnн Turbiny: Za kompaktn н objekt měřenн je zde považovбna soustava: ložiskovй stojany - ložiskovй čepy rotoru - nivelačnн body na tělesech - nivelačnн body na betonovйm zбkladu.

Cнlem je zнskбnн dat pro kontrolu a provбděnн přнpadnэch korekc н : - sprбvnйho ustavenн centricity průtočnй čбsti - vэškovб poloha ložiskovэch čepů rotoru před sespojkovбnнm - vzбjemnб poloha všech nivelačnнch bodů před připojenнm potrubн do spodku tělesa turbiny a uvedenнm TG do provozu. C) Měřenн po ukončenн montбže, před struženнm děr spojkovэch šroubů spojek a před sespojkovбnнm: Za kompaktnн objekt měřenн je zde Date: 12.11.2013 Page 184 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ