DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika CAUTION! Take care if the segments of thrust bearing are dismantled! The actual axial clearances in steam flow path are recorded in “Turbine Dozier book it can be a little different from the clearances written in drawings. Do not damage sealing strips of glands! The minimum designed axial clearance in the drawing between rotor stator is in the rear gland 2,25 mm for moving turbine rotor towards front bearing’s stand and 2,2 mm for moving of turbine rotor towards rear bearing stand (to LP casing). Work on bearings after transport to the site: UPOZORNĚNH!

V přнpadě vyjmutн kamenů axiбlnнho ložiska dejte pozor! Skutečnй axiбlnн vůle v parnн průtočnй čбsti jsou zaznamenбny v “Pasportu turbiny” – hodnoty mohou bэt mнrně rozdнlnй od vэkresovэch. Neponičte těsnнcн břity ucpбvek! Vэkresovб minimбlnн axiбlnн vůle rotor stator je 2,25 mm v břitech zadnн ucpбvky pro posun rotoru směrem k přednнmu ložiskovйmu stojanu a 2,2 mm pro posun rotoru ve směru k zadnнmu ložiskovйmu stojanu (k NT tělesu ). Prбce na ložiskбch po přepravě na elektrбrnu: · Take out the bearings. · Washing of the preservation out from bearing shells and from all supporting elements (wedges, segments). · Visual inspection of bearing shells after the turbine transport.

· Testing of the contact of collar of turbine rotor to segments inside the thrust bearing (in accordance with assembly instruction no. Q159150 ). · Checking of the clearances (measuring of the shape of bore of radial bearings, measurement of the rotor journal’s diameter and oval, checking of the side clearances in radial bearings and axial clearances in the thrust bearing after rotor putting into bearings). · Assembly of the thermocouples into bearing shells and segments as described in chapter no.2.11.9. Bearings assembly, rotor putting back into bearing shells. · Vyjmutн ložisek. · Mytн konzervace z ložiskovэch pбnvн a všech opěrnэch elementů (klнny, segmenty).

· Vizuбlnн kontrola ložiskovэch pбnvн po přepravě turbiny. · Kontrola dosedбnн kamenů axiбlnнho ložiska na nбkružek rotoru turbiny (dodržujte instrukce dle nбvodky č. Q159150 ). · Kontrola vůlн (proměřenн tvaru vrtбnн ložiska, proměřenн průměrů a ovality ložiskovэch čepů rotorů, kontrola stranovй vůle u radiбlnнch ložisek a axiбlnн vůle u segmentovйho ložiska po vloženн rotoru do ložisek). · Montбž termočlбnků do ložiskovэch pбnvн a segmentů jak je popsбno v kapitole č. 2.11.9. Montбž ložisek, spuštěnн rotoru zpět do ložiskovэch pбnvн. Clearances in bearings are designed as following: Vůle ložisek turbн ny jsou konstrukčně navrženy nбsledovně : Date: 12.11.2013 Page 191 / 278 Prepared:

O.Baroch Last Revision: Approved: P.Lešetickэ