Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika Deviation of struts position of valves’ bodies · Remove the splice bars which fix the position of supporting plates. Re-grind the surface of the consoles and the plates embedded into the top slab of foundation stool in places of welds of splice bars to be the surface flat. Lighten the valves body by crane without lifting (if necessary) and dismantle the fixture-sleeves Tp6077387 (split sleeve). Shift the supporting plates with stands according to the values on drawing Tp6064647 (slight deviation of the struts from their perpendicular position).
Take up the arosen clearances among the valve body strut foundation by turning with the ball journals pos.7 . Weld the splice-bars back to fix the supporting plates to the consoles and foundation plates in shifted position. · Uvolněte zavěšenн tělesa S T RZR na jeřбb. Notice to schemes enclosed below:
After the setting of position of valves bodies and struts according to drawing (struts are in perpendicular position to foundation, valves bodies are fixed by assembly fixtures) and after the pipes connecting to the valves nozzles, shift now the supporting plates with attached struts of stands of turbine valves according to the following scheme (shift the supporting plates of struts of stands to reach determined value on foundation in direction of arrows =deviation of the struts from perpendicular position). Deviated struts of valves bodies which were set on position would get back into perpendicular position after the pipes and turbine casings warming up during operation.
It is a change of position in comparison with the position during assembly ambient temp 20°C) position would get back into perpendicular position after the pipes and turbine casings warming up during operation. It is a change of position in comparison with the position during assembly –ambient temp 20°C) Vychэlenн polohy vzpěr STRZR ventilů: · Odtraňte přнložky fixujнcн polohu podpěrnэch desek (odbroušenн). Přebrušte do roviny povrch konzol a desek zalitэch v hornн betonovй desce zбkladovй stolice v mнstě původnнch svarů přнložek. Nadlehčete těleso ventilu jeřбbem bez zvednutн (pokud je potřeba) a demontujte fixačnн objнmky Tp6077387 (dělenй objнmky).
Proveďte posunutн podpěrnэch desek se stojбnky dle hodnot na vэkrese Tp6064647 (nepatrnй vychэlenн vzpěr z jejich kolmй polohy). Vymezte vůle vzniklй v uloženн těleso ventilu – vzpěra – zбklad vyšroubovбnнm kulovэch čepů poz.7 . Přivařte zpět přнložky a zafixujte tak podpěrnй desky v posunutй poloze ke konzolбm a zбkladovэm deskбm. · Uvolněte zavěšenн tělesa S T RZR na jeřбb. Poznбmka k nнže přiloženэm schйmatům:
Po ustavenн polohy tě les a vzp ě r ventil ů dle vэkresu (vzpěry jsou v kolmй poloze k zбkladu, t ě lesa ventil ů zafixovбna pomocн přнpravků ) a po p řipojenн potrubн na hrdla ventilů prove ďte nynн posunutн podpěrnэch desek s upevněnэmi stojбnky vzp ě r ventil ů turbiny dle nбsledujнcнho schйma (posu ň te podp ěrnй. Desky stojбnků na zбkladu o uvedenй hodnoty ve směru šipek = vykloněnн vzpě r z kolmй polohy). Vychэlenй vzpěry takto ustavenэch t ě les ventil ů by se m ě ly vlivem oh řevu potrubн a tě les turbiny za provozu dostat zp ět do kolmй polohy.
Jednб se o zm ě nu oproti poloze p ři montбži – teplota okolн 20°C) se měly vlivem ohřevu potrubн a těles turbiny za provozu dostat zpět do kolmй polohy. Jednб se o změnu oproti poloze při montбži – teplota okolн 20°C). Date: 12.11.2013 Page 208 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ