DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika due connecting of temporary piping for proceeding of post-assembly purge procedures, the necks are bevelled and blinded by plugs. Valve body, servomotors, inserts for purge procedure and struts for attachment of valves on foundation are transported in wooden boxes protect by preservation means against corrosion. Sequences of assembly works:

· Unpack the valves bodies, wash preservation from all contact surfaces for supports, attaching of actuators; piping necks blinding remove always just before the assembly · Check the drawing of axis on foundation a draw the position of supports. Prepare the preparations for fixing of supports of valves bodies on position (acc.to chapter Positioning of IPSI valves · Hung the body of valve on crane by fastening of body, the weight of valve without actuators is 11,56 tons (13,56 tons including actuators). Assemble supports of valves and place valves on position acc.to chapter Positioning of IPSI valves · Take out the piping necks blinds, wash the preservation.

Right now are the valve bodies ready for connecting to the piping. · In first assemble cross-over pipink (shaped piece), then connect main inlet steam pipelines TR711x15,87 , in the end connect little piping of warming and drainage of chambers. Main steam inlet pipelines have to be set to the necks and freely hung on suspensions just before welding to the bodies. Checking the valves bodies’ position during welding. · Dismantle inner components of valves and assemble the preparations for carrying out of blowing through and flushing of inlet steam pipelines acc.to Tp6073213 . The valve-inserts for proceeding of purge procedures on steam inlet pipelines:

provizornнho potrubн k vykonбnн pomontбžnнch čistнcнch operacн, hrdla jsou naъkosovanб a zaslepenб zбtkami. Těleso ventilu, servopohony, přнpravky pro čistнcн operace a podpěry pro upevněnн ventilů na zбklad jsou transportovбny v dřevěnэch bednбch, chrбněny proti korozi konzervačnнm prostředkem. Postup montбžnнch pracн: · Tělesa ventilů vybalit, stykovй plochy pro podpěry dekonzervovat, kontaktnн plochy pro upevněnн servopohonů a zбslepky hrdel potrubн odkrэvat vždy až těsně před montбžн. · Kontrolovat orэsovбnн os na zбkladu a zakreslit polohu podpěr.

Připravit přнpravky pro fixaci podpěr těles ventilů na pozici (dle kapitoly “ Ustavenн těles STRZZ ventilů · Zavěsit těleso ventilu na jeřбb opбsбnнm tělesa, hmotnost ventilu bez servopohonů je 11,56 tuny (13,56 tuny včetně servopohonů). Montujte podpěry ventilů a uložte ventil na pozici dle kapitoly “ Ustavenн těles STRZZ ventilů · Sejmout zбslepky hrdel potrubн, odstranit konzervaci. Tělesa ventilů jsou nynн připravena pro připojenн k potrubн. · Montujte nejprve převбděсн potrubн (tvarovky), potй připojit hlavnн přнvodnн parovody TR711x15,87 a nakonec drobnб potrubн prohřevu a odvodněnн komor.

Před přivařenнm musн bэt hlavnн přнvodnн parovody přirovnбny k hrdlům a volně zavěšeny na zбvěsech. Během svařovбnн kontrolujte polohu těles ventilů. · Demontujte vnitřnн dнly ventilů a namontujte přнpravky pro provedenн profuku a proplachu přнvodnнch parovodů dle vэkresu Tp6073213 . Vestavba ventilu pro vykonбnн čistнcнch operacн na potrubн přнvodu pбry: Date: 12.11.2013 Page 211 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ