Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika · After flushing and blowing through of inlet steam pipelines it is possible to dismantle provisory preparations and to assemble back inner components of valves, actuators and position sensors. Set the outer edge of protection layer of sealing rings pos.111, 115ч120 toward the actuators during assembly. During the assembly pre-strained the gland rings pos.125 by tightening of nuts pos.79 . Check the pre-stress of Belleville springs of valve glands by tighten of nuts M16 pos.79 with controlled torque 32 N.m .
Carry out the greasing for all bolts and sealing surfaces with anti-sizing Molykote G Rapid+ . Make a record about the length of spring bundles Lo, Lx. · Threads of bolts M64x4 pos.60 and faces of nuts pos.75 (flanges of valve body and cover pos.3 and 4) degrease and at first apply the sliding varnish Molykote D321R and then apply the anti-sizing compound Molykote G Rapid+ ; then gradually tighten the nuts with controlled torque 4100N.m .
· Threads of bolts M30 pos.61 and faces of nuts pos.76 (cover pos.3 and 4 and stands for actuators pos.35 and 36) degrease and at first apply the sliding varnish Molykote D321R and then apply the anti-sizing compound Molykote G Rapid+ ; then gradually tighten the nuts with controlled torque 450 N.m . Carry out the coupling of valve spindles with the actuators including fitting of insertion piece pos.56 (with material allowance 5mm for fitting) so it will be kept the dimension 108 in closed · Po provedenн proplachů a profuků přнvodnнch parovodů, demontujte provizornн přнpravky a namontujte zpět vnitřnн dнly ventilu, servopohony a čidla polohy.
Těsnнcн kroužky poz.111, 115ч120 nastavit při montбži ochrannou vrstvou vnějšн hrany směrem k pohonům. Ucpбvkovй kroužky poz.125 při montбži předepnout dotaženнm matic poz.79 . Kontrolujte předpětн talнřovэch pružin ucpбvek ventilu tj. utaženн matic M16 poz.79 utahovacнm momentem 32 N. m. Mazбnн provбdějte pro všechny šrouby a třecн plochy pastou Molykote G Rapid+ . Protokolujte dйlky svazku pružin Lo, Lx. · Na zбvity šroubů M64x4 a čela matic poz.75 (přнruby tělesa ventilu a vнk poz.3 a 4) naneste po odmaštěnн nejprve kluznэ lak Molykote D321R a potй protizбděrovou pastu Molykote G Rapid+ a postupně utahujte matice momentem 4100 N. m.
· Na zбvity šroubů M30 poz.61 a čela matic poz.76 (Vнk poz.3 a 4 a stojбnků poz.35 a 36 servopohonu) naneste po odmaštěnн kluznэ lak Molykote D321R a protizбděro vou pastu Molykote G Rapid+ a postupně utahujte matice momentem 450 N. m. Proveďte sespojkovбnн vřeten ventilů se servopohony, včetně dolнcovбnн vložek poz.56 (s přнdavkem na dolнcovбnн 5mm), tak aby v zavřenй poloze byla dodržena kyta 108, dle detailu D1 na Date: 12.11.2013 Page 212 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ