DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika The following notes are connected for event, if the control valves are dismantle from the chamber and assembled back on site: Ш Take away the blinds of chambers, unwrap and wash the conservation. Decrease the contact surfaces of flanges. Assembly the stud screws pos.43 (M56x4) Degrease the parting plane. Ш Assembly the stand of valve pos.2,3 (3 valves) on the valve chamber. Assembly the washers and nuts M56 x 4 (poz.55, 72) .

The thread of screws and the faces of nuts have to be covered with the sliding lack Molykote D321R and with anti-size compound Molykote G Rapid+ . Tighten the nuts pos.55 (M56x4 ) with torque of 2870 N. m. Check the deformation of gap in the flange during the tightening. The deformation must not be bigger then 0,1 mm . Ш Check the clearances delimitation and the demontovat od komory a zpětně montovat: Ш Sejměte zбslepky komor, vybalte a dekonzervujte. Odmastěte těsnнcн plochy přнrub. Montujte zбvrtnй šrouby M56x4 poz.43 . Odmastěte dělнсн rovinu. Ш Montujte stojбnky ventilu poz.2,3 jednotlivэch ventilů ( 3 ventily ) na ventilovou komoru. Montujte podložky a matice M56 x 4 (poz.55, 72 ).

Zбvit šroubů a čela matic musн bэt pokryty kluznэm lakem Molykote D321R a protizбděrovou pastou Molykote G Rapid+ . Matice poz.55 ( M56x4 ) utahujte krouticнm momentem 2870 N. m. Kontrolujte však deformaci spбry přнruby během utahovбnн. Deformace nesmн bэt většн než 0,1mm . Ш Kontrolujte vymez enн a nastavenн sprбvnэch vůlн. Ш Kontrolujte zakolнkovбnн dнlů. Kontrolujte nбplň ložisek. Ш Proveďte kontrolu nastavenн ventilů dle vэkresu Tp6073670 (začбtek otevнrбnн, zdvih).

Ш Proveďte dotaženн matic poz.61 momentem 26N.m a matic poz.60 momentem 94N.m pro dosaženн sprбvnйho předepětн talнřovэch pružin ucpбvek poz.115 a 116 , dodržujte zбsady nбvodky Q 159 155 , ъdržbu ucpбvek provбdět dle předpisu firmy Chesterton. Ш Ostatnн instrukce dodržujte dle vэkresu č. Tp6073670. Ш Pro utahovбnн nespecifikovanэch šroubů vyberte moment podle tabulky v tomto manuбlu. Ш Mazбnн provбdějte pro všechny šrouby pastou Molykote G Rapid+ . Pokud je předepsбno mazat kluznэm lakem, použijte Molykote D321R . right clearances setting. Ш Check if all pins are assembled. Check if the filling is inside role-contact bearings. Ш Check the right valve’s position setting acc.

to drawing Tp6073670 (start of valve opening, stroke). Ш Complete the nuts tightening pos.61 with torque 26N.m and the nuts tightening pos.60 with torque 94N.m for reaching of right pre-stress of plate springs of the bushings pos.115 and 116 , keep the instructions in guide Q 159 155 , maintenance of bushings perform acc. to Chesterton instructions. Ш Keep the other instructions according to the drawing Tp6073670. Ш For tightening of unspecified bolts choose the torque acc. to the table in this manual. Ш Perform all the screw’s greasing with anti - size compound Molykote G Rapid+ . Apply Molykote D321R if there is prescribed the sliding lack using. Date: 12.11.2013 Page 218 / 278 Prepared:

O.Baroch Last Revision: Approved: P.Lešetickэ