DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika gasket pos.106 insert the spacing washer with the same tickness, use the 8 pcs. of bolts, nuts and tighten them only to 50% of their final prescribed torque. The thread ends of bolts and faces of nuts must be covered by slip varnish Molykote D321R and lube paste Molykote G Rapid+. · Weld on the steam piping to counter flange assembled onto stop valve. Before the welding the inlet piping must be fit to the socket of counterflange while the pipeline is hung on free suspensions.

Check the flange faces collinearity as written in · Attach the servomotor to the stop valve including the connection to valve spindle. Assembly the piping of HP control system, the warming-trough and drainage system piping (do not weld the piping before the completion of the steam inlet piping blowing through). · Before the purifying by the steam blowing or by the chemical flushing, there is necessary to fix the pipe of steam inlet piping, dismantle the stop valve, connect the provisional piping to flange pos.1. · After steam inlet piping blowing through completion, dismantle the provisional piping, assemble the stop valve including the gaskets.

The nuts of flange between the stop valve and the control valve chamber (pos.57 - Tp6073670 ) tighten with controlled torque 980 Nm. The nuts between steam inlet piping and stop valve tighten slightly fist of all - only for proper contact in flange, after that remove the fixtures of steam inlet piping and tighten the screws (pos.28 - Tp6067929 ) by torque 1660 Nm. During the tightening of both flanges check the gap around the screws of flange must not be close more than 0,2 mm (with comparsion of the gap in initial state = fit close and slight prestres of screws). · Assembly the piping of HP hydraulic control system, weld the warm-up and drainage piping, assembly the thermal insulation.

· Check the nuts pos.42 tightening with torque 26 N.m for the reaching of compression of glands (lubricate with anti-sizing compound only). During assembly of glands keep the guide Q1 59 155. · Apply the anti-size compound on the thread of screws pos.28, 31 and on the face of their nuts pos. 39, 41. The bolts pos.31 tighten up with the stuffing pos.68 to the size „X“ was the same without the stuffing, the bolts pos.34 distančnн vložku stejnй tloušťky, použнt min. 8 šroubů, matice šroubů dotahovat na 50% konečnйho dotahovacнho momentu. Zбvitovй konce šroubů a čela matic musн bэt pokryty kluznэm lakem Molykote D321R a mazacн pastou Molykote G Rapid+.

· Proveďte přivařenн parovodu k přнrubě namontovanй na RZ ventilu. Před přivařenнm musн bэt přнvodnн potrubн přirovnбno k hrdlu protipřнruby při volnйm zavěšenн potrubн na zбvěsech. Proveďte kontrolu rovnoběžnosti čel přнrub viz. · Proveďte montбž servopohonu RZ ventilu včetně připojenн k vřetenu ventilu. Montujte potrubн VT hydrauliky, prohřevu a odvodněnн (nepřivařovat ale dřнve než bude proveden profuk přнvodnнho parovodu). · Na provedenн profuku nebo chemickйho čištěnн parovodu je nutno zafixovat přнvodnн potrubн, demontovat RZ ventil, připojit provizornн potrubн na přнrubu poz. 1.

· Po skončenн čištěnн přнvodnнho parovodu je nutno demontovat provizornн potrubн namontovat RZ ventil včetně těsněnн. Matice na přнrubě s komorou regulačnнch ventilů (poz.57 - Tp6073670 ) u tahujte kontrolovanэm momentem 980 N.m. Matice mezi přнvodnнm parovodem a RZ ventilem nejprve dotahujte lehce na dosednutн, potй odstraňte fixace polohy paro vodu a proveďte utaženн šroubů (poz.28 - Tp6067929 ) momentem 1660 N.m. Během postupnйho utahovбnн obou přнrub kontrolujte spбru okolo šroubů přнruby – nesmн se zavřнt o vнce než 0,2mm (porovnбnн velikosti spбry v počбtečnн pozici = dosednutн a mнrnй napruženн šroubů).

· Proveďte montбž potrubн VT hydrauliky, přivařenн potrubн prohřevu a odvodněnн, montбž tepelnй izolace. · Proveďte kontrolu dotaženн matic poz.42 dotlačovacнch šroubů pro předepnutн ucpбvky momentem 26 N.m (mazбnн pouze protizбděrovou pastou). Při montбži ucpбvky dodržujte nбvodku Q159 155. · Zбvity šroubů poz.28, 31 a čela jejich matic poz.39, 41 namažte pouze protizбděrovou pastou bez kluznйho laku. Šrouby poz.31 musн bэt dotaženy tak, aby byla dodržena mнra „X“ při odměřenн bez použitн těsnнcнho kroužku Date: 12.11.2013 Page 220 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ