Komatsu PC210-8, PC210LC-8, PC210NLC-8, PC230NHD-8, PC240LC-8, PC240NLC-8 — E-3 Engine does not start (Engine does not turn)

UEN00244-00 40 Troubleshooting 12 PC210, 230, 240-8 Possible causes and standard value in normal state Cause Standard value in normal state/Remarks on troubleshooting 7 Defective starting motor (Internal defect) a Prepare with starting switch OFF, then turn starting switch to START and carry out troubleshooting. Starting motor terminals Voltage Between B (SB) – chassis ground Power supply 20 – 30 V Between C (SC) – chassis ground Starting input 20 – 30 V If power supply and starting input are normal but starting motor does not turn, starting motor is defective.

8 Defective alternator (Internal short circuit) a Prepare with starting switch OFF, then turn starting switch ON and carry out troubleshooting. Alternator Voltage Between L – chassis ground Generation output Max. 1 V 9 Disconnection in wiring har- ness (Disconnection in wiring or defective contact in con- nector) a Prepare with starting switch OFF, then carry out troubleshooting without turning starting switch ON. Wiring harness between H15 (female) (4) – J01 – R06 (female) (5) Resis- tance Max. 1 z Wiring harness between R06 (female) (3) – R07 (female) (4) Resis- tance Max. 1 z Wiring harness between R07 (female) (3) – R17 (female) (1) Resis- tance Max.

1 z Wiring harness between starting motor safety relay B – heater relay – battery relay B Resis- tance Max. 1 z Wiring harness between starting motor safety relay E – chassis ground Resis- tance Max. 1 z Wiring harness between starting motor safety relay C – starting motor C (SC) Resis- tance Max. 1 z Wiring harness between F01-3 – S14 (male) (1) Resis- tance Max. 1 z Wiring harness between S14 (male) (3) – R06 (female) (1) Resis- tance Max. 1 z Wiring harness between R06 (female) (2) – J04 – chassis ground (T04) Resis- tance Max.

1 z 10 Ground fault in wiring har- ness (Short circuit with GND circuit) a Prepare with starting switch OFF, then carry out troubleshooting without turning starting switch ON. Wiring harness between H15 (female) (4) – J01 – R06 (female) (5), – circuit branch end Resis- tance Min. 1 Mz Wiring harness between R06 (female) (3) – R07 (female) (4) Resis- tance Min. 1 Mz Wiring harness between R07 (female) (3) – R17 (female) (1) Resis- tance Min. 1 Mz Wiring harness between starting motor safety relay B – heater relay – battery relay B Resis- tance Min. 1 Mz Wiring harness between starting motor safety relay C – starting motor C (SC) Resis- tance Min.

1 Mz Wiring harness between F01-3 – S14 (male) (1) Resis- tance Min. 1 Mz Wiring harness between S14 (male) (3) – R06 (female) (1) Resis- tance Min. 1 Mz 11 Hot short (Short circuit with 24V circuit) in wiring harness a Prepare with starting switch OFF, then turn starting switch ON and carry out troubleshooting. Wiring harness between R17 (female) (2) – alternator L, – circuit branch end Voltage Max. 1 V