Freightliner FLD Conventional — FLD Conventional

Transmissions accelerator. Press and release the clutch pedal. After releasing the clutch, accelerate again. For 18-speed transmissions: Continue upshifting through the shift pattern. Double-clutch during lever shifts (6th to 7th to 8th); single-clutch during split shifts (6th direct to 6th overdrive, etc.). Continue downshifting from 4th overdrive to 4th direct, then 4th direct to 3rd overdrive, 3rd over- drive to 3rd direct, etc. Single clutch when split shifting (direct to overdrive, overdrive to direct). Double clutch when making lever shifts (4th to 3rd, 3rd to 2nd, etc.). For 18-speed transmissions: IMPORTANT:

Never use the clutch brake when downshifting, or as a brake to slow the vehicle. To shift from 5th direct to 5th overdrive, move the splitter control button ( Fig. 8.5 ) into the overdrive (forward) position, then immediately release the accelerator. Press and release the clutch pedal. After releasing the clutch, accelerate again. Eaton Fuller Deep-Reduction Models Continue upshifting through the shift pattern. Double-clutch during lever shifts (6th to 7th to 8th); single-clutch during split shifts (6th direct to 6th overdrive, etc.). Refer to the Eaton website for additional information, www.roadranger.com. Downshifting General Information, Deep-Reduction 10-Speed RTO Models 1.

Downshift from 8th overdrive to 8th direct without moving the shift lever. Flip the splitter control but- ton to the direct (rearward) position; then, imme- diately release the accelerator, and disengage the clutch. Engage the clutch, and accelerate the engine only after the transmission has shifted. Eaton Fuller 10-speed RTO model transmissions have a 5-speed front section, and a 2-speed rear- range section, with a deep reduction gear. The low- low, deep reduction gear is used only when operating under adverse conditions. Low gear in the front sec- tion is used only for rough, off-highway conditions, as a starting ratio.

The remaining four forward positions are used once in the low range and once in the high range. See Fig. 8.6 for the shift pattern, noting that the 3rd/7th and 4th/8th shift positions in the RTX-LL transmissions are opposite of the RTO-LL transmissions. 2. Start the downshift from 8th direct to 7th over- drive by flipping the splitter control button to the overdrive (forward) position; then, immediately double-clutch through neutral, moving the shift lever from 8th to 7th gear. 3. Shift downward through each of the high range gears, alternating the procedures in steps 1 and 2, above, until reaching 5th direct. 1 4 5 8 A B 1 1 3 5 7 4.

While in 5th direct and ready for the downshift to 4th (13-speed transmissions) or 4th overdrive (18-speed transmissions), push the range prese- lection lever down. Then, double-clutch through neutral and move the shift lever to the 4th gear position. On 18-speed transmissions, move the splitter control button to the overdrive (forward) position before engaging the clutch. Do not move the control button while the shift lever is in neu- tral. N N C D 6 7 3 2 E F 2 6 8 4 03/13/96 f260026a 5. Continue downshifting from 4th to 1st as follows: A. All RTO Transmissions B. All RTX Transmissions C. Up for High Range D. Down for Low Range E. Forward for IN F.

Rearward for OUT For 13-speed transmissions: Downshift through the low range gears as condi- tions require. 1. Deep Reduction Button Fig. 8.6, Eaton Fuller 10-Speed RTO Model Transmissions Shift Patterns 8.7