mercedes-benz — Mercedes-Benz Automated-Manual Transmissions Troubleshooting Guide

Chassis Electrical Control Systems 54.40 General Information amps. The 2010 CHM does not have the current sourcing ability to drive these solenoids, so a relay in the chassis PDM is added to the circuit. The ener- gized solenoid opens and directs air flow by means of a three-port valve. An open solenoid removes the air supply to the rear suspension and vents the exist- ing suspension pressure, allowing the rear of the ve- hicle to be lowered. Fifth Wheel Slide Controls With the engine running, the fifth wheel slide can be activated using a momentary, two-position smart switch. Pressing the upper half of the fifth wheel slide switch activates the fifth wheel slide.

Pressing the upper half of the fifth wheel slide switch again deacti- vates the fifth wheel slide. See Fig. 4 . If the fifth wheel slide is activated and the engine is turned off, the system will deactivate the fifth wheel slide. Driv- ers may activate the fifth wheel slide when vehicle speeds are below 8 mph (13 km/h). The fifth wheel slide automatically deactivates when the vehicle reaches speeds greater than 10 mph (16 km/h). Feedback from the suspension dump solenoid air circuit is required for correct operation of the suspen- sion dump controls. Feedback is provided by a ground input to the CHM. The input is at ground when a pressure switch within the AMU solenoid closes.

On AAVA-equipped vehicles, the pressure switch is in the air line. A grounded feedback circuit from the closed pressure switch indicates that the system is activated. An open feedback circuit indi- cates that the suspension dump is not activated (sus- pension dump switch is not turned on), or there is a malfunction (suspension dump switch is turned on but the pressure switch is still open). SLIDE On a suspension dump with a lock solenoid, there is a second normally open AMU/AAVA solenoid that activates a double check valve in the rear suspen- sion air supply. This valve keeps the rear suspension in the last selected state when the engine is turned off.

This feature permits an override of the automatic refill, allowing the suspension to stay lowered. The lock solenoid receives power through a BHM- supplied splice pack. f610793 02/15/2006 Fig. 4, Fifth Wheel Slide Switch When the fifth wheel slide switch is activated, the CHM activates a low-current output to a normally closed air management unit (AMU) solenoid. On AAVA vehicles, the solenoid current is about 1.5 amps. The 2010 CHM does not have the current sourcing ability to drive these solenoids, so a relay in the chassis PDM is added to the circuit. The ener- gized solenoid opens and supplies pressurized air to an air cylinder located on the fifth wheel.

The cylin- der operates a mechanical linkage that moves two plunger arms that are used to lock the fifth wheel in position. The spring return plungers are located on each rail of the fifth wheel mounting assembly. When the air cylinder is pressurized, the plungers withdraw and the fifth wheel is free to slide along the mounting rails. When the fifth wheel slide is deactivated, the springs on the linkage arms return the plungers to a lock position on the rails. See Fig. 5 . A remote-activation switch is commonly installed in ambulances so that the suspension dump can be activated when the rear door opens.

Freightliner pro- vides a circuit that the body builder uses to install a remote-activation switch. The remote-activation switch is usually located at the rear of the ambu- lance. The remote-activation switch receives power through a direct wiring connection to the BHM. Fifth Wheel Slide A sliding fifth wheel is an option on an M2 vehicle. A sliding fifth wheel allows the weight of the trailer to be transferred between the tractor axles, thereby in- creasing or decreasing the distance between the front of the trailer and the back of the cab. A sliding fifth wheel can be adjusted to allow enough distance between the trailer and the cab to prevent the trailer from hitting the cab during a turn.

Feedback from the fifth wheel slide air cylinder circuit is required for correct operation of the fifth wheel slide controls. Feedback is provided by a ground input to the CHM. The ground input is delivered when a pressure switch within the AMU solenoid closes. On AAVA-equipped vehicles, the pressure Business Class M2 Workshop Manual, Supplement 22, September 2012 050/4