94 Maintenance Section Engine Oil and Filter - Change Table 37 Program A Verification for an Oil Change Interval of 500 Hours This program consists of three oil change intervals of 500 hours. Oil sampling and analysis is done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all of the results are satisfactory, the 500 hour oil change interval is acceptable for the engine in that application. Repeat Program A if you change the application of the engine. If a sample does not pass the oil analysis, take one of these actions: Shorten the oil change interval to 250 hours.
Proceed to Program B. Change to a preferred oil type in Table 37. Program B Optimizing Oil Change Intervals Begin with a 250 hour oil change interval. The oil change intervals are adjusted by increments. Each interval is adjusted an additional 50 hours. Periodic oil sampling and analysis is done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the engine. (1) The standard oil change interval in this engine is 500 hours, if the operating conditions and recommended oil types that are listed in this table are met. The traditional oil change interval for engines is 250 hours.
Improvements in the engine allow this engine oil change interval. This new standard interval is not permitted for other engines. Refer to the applicable Operation and Maintenance Manuals for the other engines. (2) Normal conditions include these factors: Fuel sulfur below 0.3%, altitude below 1830 m (6000 ft), and good air filter and fuel filter maintenance. Normal conditions do not include high load factor, harsh operating cycles, or harsh environments. (3) High load factors can shorten the service life of your engine oil. Continuous heavy load cycles and very little idle time result in increased fuel consumption and oil contamination. These factors deplete the oil additives more rapidly.
If the average fuel consumption of your engine exceed 43 L (11 US gal) per hour, follow the “High Load Factor” recommendations in Table 37. To determine average fuel consumption for your engine, measure average fuel consumption for a period of 50 to 100 hours. If the application of the engine is changed, the average fuel consumption may change. (4) For sulfur content above 0.5%, refer to Operation and Maintenance Manual, “Total Base Number (TBN) and Fuel Sulfur Levels for Direct Injection (DI) Diesel Engines” in the “Lubricant” section of this manual. Also, you may refer to this topic in Manual, SEBU6251. (5) In order to verify an oil change interval of 500 hours, refer to “Program A” below.
(6) Use “Program B” below to determine an appropriate interval. If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above. References Reference: Form, PEDP7035, “Optimizing Oil Change Intervals” Reference: Form, PEDP7036, “S·O·S Fluid Analysis” Reference: Form, PEDP7076, “Understanding the S·O·S Oil Analysis Tests” Oil Grade Plug The Oil Grade Plugs are used on the C-9 Industrial engine to enhance start-up in cold weather conditions. When changing oil grades, the operator must ensure that the corresponding plug is inserted into the wiring harness.
The oil grade plugs can be recognized by either the identification tags or by the color of the wires. For the location of the oil grade plug, refer to Operation and Maintenance Manual , “Sensor and Electrical Components”. Adjustment of the Oil Change Interval Note: Your Caterpillar dealer has additional information on these programs.
Oil Change Interval for C-9 Industrial Engine (1) Multigrade Oil Type Operating Conditions Normal(2) High Load Factor above 43 L (11 US gal per hour of fuel) (3) Severe Fuel Sulfur from 0.3% to 0.5% (4) Altitude above 1830 m (6000 ft) Cat DEO Preferred 500 hr 500 hr 500 hr 250 hr(6) API CH-4 11.0 minimum TBN(4) Preferred 500 hr 500 hr 500 hr 250 hr(6) API CH-4 TBN(4) below 11.0 500 hr 500 hr 250 hr(5) 250 hr(6) API CG-4 500 hr 250 hr(5) 250 hr(5) 250 hr(6) API CF-4 250 hr(5) 250 hr(6) 250 hr(6) 250 hr(6)