Freightliner — FLA COE, FLB COE, FLC112 Conventional, FLD Conventional, FLL COE

Engine Cooling/Radiator 20 Maximum Coolant Protection in °F (°C) at Various Antifreeze Concentrations Cooling System Capacity: gal (L) * Ethylene-Glycol Base Antifreeze Required: gallons (liters) 2 (8) 3 (11) 4 (15) 5 (19) 6 (23) 7 (26) 8 (30) 9 (34) 10 (38) 11 (42) 12 (45) 20 (76) 16 (–9) 10 (–12) 4 (–16) (–19) (–24) (–30) (–37) (–44) (–52) * For cooling system capacities not shown, the required amount of antifreeze can be calculated, using the following: Ethylene-glycol base antifreeze in a 25% solution protects to 10°F (–12°C), 33% to 0°F (–18°C), 40% to (–24°C), 50% to (–37°C), and 60% to (–52°C).

60% ethylene-glycol base antifreeze and 40% water by volume gives maximum coolant protection [–52°C]). Exceeding 60% antifreeze diminishes coolant protection; concentrated ethylene-glycol base antifreeze will freeze at approximately 0°F (–18°C). Table 5, Maximum Coolant Protection in Degrees F (Degrees C) at Various Antifreeze Concentrations 20–03 Fan Drive and Clutch Checking (Noise Emission Control) gine could start up without warning, resulting in serious personal injury. 2.1 If equipped with an electric thermal switch, make sure the engine is not run- ning. Put the ignition switch in the ON position (engine shut down).

Place a jumper between the thermal switch con- nectors (located in the engine thermostat housing), while observing the fan clutch. The fan clutch should be seen and heard engaging. Eaton Viscous Fan Clutch Periodic maintenance is not required because an Eaton viscous fan drive is a sealed unit. However, periodically check it for damage and for correct op- eration. If the fan drive is inoperative or damaged, replace it with a new one. See Group 20 of the Heavy-Duty Trucks Service Manual for instructions. Horton Advantage ® and HT 55O Fan Clutch If equipped with a fanstat (shutterstat), run the engine until its temperature is above the fanstat engagement setting of 195°F (91°C).

The fan clutch should en- gage, causing the fan to turn. WARNING NOTE: If any part of the fan clutch needs to be fixed or replaced, after performing the checks below, see Group 20 of the Heavy-Duty Trucks Service Manual. Wear safety goggles when draining the air system or loosening an air line, because dirt or sludge could fly out at high speeds. Do not direct the air- stream at anyone. Do not disconnect pressurized hoses, since they may whip as air escapes. Fail- ure to take all necessary precautions could result in personal injury. 1. Inspect all electrical connections and wires. Tighten the connections if loose, and replace wires and connections if damaged. 2.

Charge the air system to 120 psi (627 kPa), then proceed as follows: 2.2 If the fan clutch does not engage, see if compressed air is in the fan clutch actuat- ing air line: With the ignition on, but the engine shut down, slowly loosen the fit- ting that connects the actuating air line to the fan clutch; do not disconnect the fit- ting. If compressed air escapes, the fan clutch is inoperative and must be re- paired. If no compressed air escapes, replace the solenoid valve or fanstat, as applicable. Tighten the fitting. WARNING Do not jumper the thermal switch while the engine is running. This could start the cooling fan, which could result in serious personal injury.

If the vehicle is equipped with Detroit Diesel Opti- mized Idling ® , make sure this feature is not acti- vated. If Optimized Idling were activated, the en- Heavy-Duty Trucks Maintenance Manual, January 2007 20/5