CTM100 (06APR04) 03-120-5 P OWER T ECH 10.5 L & 12.5 L Diesel Engines 040604 PN=337 Base Engine Operation A—Oil Pump H—Oil Cooler Relief Valve N—Idler Gear Bushing S—Valve Rocker Arm Rollers B—Oil Cooler I—Main Oil Galley O—Oil Pump Drive Gear T—Electronic Unit Injector C—Oil Filter J—Piston Spray Jets Bushing Lube U—Turbocharger Lube Line D—Oil Filter Bypass Valve K—Crankshaft Main Bearing P—Rocker Arm Shaft Oil V—Return Oil E—Oil Cooler Bypass Valve L—Connecting Rod Bearing Supply W—Pressurized-Nonfiltered Oil F—Oil Pressure Regulating M—Rocker Arm Shaft Q—Unit Injector Rocker Arm X—Pressurized-Filtered Oil Valve Assemblies R—Unit Injector Rocker Arm G—Pick-up Tube Roller Bushing The lubrication system consists of a crankshaft driven allow oil to flow to the crankshaft cross-drilled oil pump (A), oil cooler (B), oil filter (C), oil filter bypass passages.
The crankshaft cross drilled passages route valve (D), oil cooler bypass valve (E), and oil pressure oil flow from a main journal to each connecting rod regulating valve (F). bearing. Oil is drawn from the sump via a pick-up tube (G) and A drilled passage (O) at the front of the block routes an internal passage in the cylinder block. The oil pump lubrication oil to the oil pump. A cross drilled passage sends the oil to the pressure regulating valve housing in the pump housing routes this oil to the outside edge and then to the oil cooler through an internal passage of the pump. This oil lubricates the oil pump gear in the cylinder block. An oil cooler relief valve (H) bushing.
protects the oil cooler during cold oil starting by returning oil to sump. The cooler bypass valve allows A drilled passage from the number one main bearing oil to bypass the cooler and flow to the filter if the oil routes oil to the upper idler gear hub. A drilled cooler is restricted. From the oil cooler oil flows to the passage in the hub routes oil to the outside edge of oil filter housing and into the filter. If the filter becomes the hub. This oil lubricates the upper idler gear restricted, the oil filter bypass valve will open sending bushing. oil to the main oil galley.
A drilled passage in the cylinder block connects with Oil flow from the filter is sensed by the oil pressure the upper idler passage. This oil is available to regulating valve. This valve regulates the pressure in lubricate auxiliary drive components. the main oil galley (I). Excess oil is returned to sump. Two drilled passages route oil from the main oil galley Clean cool oil is routed directly from the top of the filter through the cylinder block towards the head. At the base (U) to the turbocharger. Turbocharger return oil is head gasket, oil flows into head bolt holes 19 and 23.
routed through a steel line to the cylinder block and Oil flows around these bolts and into a cross-drilled then to sump. passage at the top of the head. Steel lines (P) connect with the cross drilled passages and routes oil to a The remaining oil is routed to the main oil galley then rocker arm shaft hold down clamp for each rocker arm distributed to the piston spray jets (J), crankshaft main shaft. bearings (K), connecting rod bearings (L), the two rocker arm shaft assemblies (M), upper idler gear At the rocker arm hold down clamp, oil flows around a bushing (N), and auxiliary drive. cap screw and enters the rocker arm shaft assemblies (M).
The rocker arm shaft is hollow and is sealed on The piston spray jets receive oil directly from the main each end. A hollow roll pin connects with each rocker oil galley. These spray jets allow for precise targeting arm shaft drilled passage and routes oil to the two of the oil spray onto the bottom of the piston. center camshaft bushings. Drilled passage in the block route oil directly to each crankshaft main journal. The main bearing is slotted to Continued on next page RG,RG34710,1519 –19–16SEP02–2/3 03 120 5