Delphi — Cooling System Operation

CTM100 (06APR04) 03-120-9 P OWER T ECH 10.5 L & 12.5 L Diesel Engines 040604 PN=341 Base Engine Operation A—Coolant Pump F—Directed Top Liner Cooling I—Water-to-Air Aftercooler L—High Temperature Coolant B—Coolant Heater Passages Supply M—To Radiator Top Tank C—Coolant Manifold G—Directed Top Liner Cooling J—Water-to-Air Aftercooler N—From Radiator D—Thermostats Return Line Return O—Coolant Passage E—Thermostat Housing H—Coolant Bypass Tube K—Low Temperature Coolant P—Unit Injector Sleeve The pressurized cooling system consists of a radiator The larger and higher number of coolant flow holes (not shown), coolant pump (A), coolant heater (B), around cylinders 5 and 6 force more coolant to flow to coolant manifold (C), coolant passages in block and the back of the cylinder head than to the front.

the cylinder head, thermostats (D), and thermostat housing (E). Once coolant is in the cylinder head, all flow is towards the front. Coolant from cylinder 6 flows forward and The coolant pump draws coolant from the radiator accumulates with flow from other cylinders. All coolant through the lower radiator hose. Flow then goes past a flow then exits out the head at number 1 cylinder to coolant heater and into the oil cooler housing. Coolant the thermostat housing. flows around the oil cooler and then flows into one of two circuits. The second circuit is called the “directed top liner cooling” system.

Two drilled passages (F) at the top of The main circuit flows coolant from the oil cooler into the oil cooler cavity in the cylinder block route coolant the coolant manifold. The coolant manifold extends the to cylinders 3 and 4 liners for top liner cooling. length of the right side of the block. From the coolant manifold, coolant flows into each liner cavity. From the Coolant will flow around the top of cylinder 3 liner, then liners, coolant flows up into the cylinder head. flow forward to cylinder 2 liner and then to cylinder 1 liner. Coolant will leave cylinder 1 through a drill The coolant flow through the block and cylinder head passage to the thermostat housing.

Coolant entering is optimized to provide ample flow around each liner number 4 cylinder will flow rearward to number 5 and and to provide more flow to the rear of the cylinder then to number 6. Coolant leaves number 6 cylinder head than into the front. To achieve this, the coolant through a drilled passage and flows though an external passages from the block to the cylinder head vary in steel line (G) to the thermostat housing. size and in number. When the engine is cold, the thermostats will be The holes on the right side of the block are smaller closed. Coolant will flow through the bypass tube (H), than the holes on the left side. Therefore, as coolant into the inlet of the coolant pump.

flows out of the coolant manifold on the right side of the block, it is forced to flow around the liners to When the engines warms to operating temperature, escape through larger holes on the left of the block. the thermostats will open and coolant will flow past the This assures that each liner is surrounded by coolant open thermostats to the radiator (M). flow. The thermostat housing contains two thermostats. The In addition, there are more holes and larger holes at bottom thermostat has a blocking poppet. When the the rear of the cylinder head than at the front.

engine gets to operating temperature, this thermostat Cylinders 1 and 2 have one 6.3 mm (0.25 in.) and one will open and allow flow to the radiator. The blocking 9 mm (0.35 in.) hole. Cylinders 3 and 4 have two 6.3 will close off the bypass path to the coolant pump inlet. mm (0.25 in.) and two 10 mm (0.39 in.) holes. Cylinders 5 and 6 have two 10 mm (0.39 in.) and two 16 mm (0.63 in.) holes. Continued on next page RG,RG34710,1521 –19–09SEP02–2/3 03 120 9