Atari · Battlezone TM-184 · 7 pp.

Atari Battlezone TM-184 Open-Face Conversion Kit Installation Instructions PDF

Related manuals

Contents

Document text

Battlezone Open-Face Conversion Kit TM-184 1st Printing_Page_1.png

TM. 184 1st printing Battlezone” ee Open-Face Conversion Kit | installation Instructions

Page 1

Battlezone Open-Face Conversion Kit TM-184 1st Printing_Page_2.png

NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below. WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service Atari, Inc. : California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) age From California, Alaska or Hawaii & (408) 745-2900 egw From anywhere else in this area toll-free (800) 538-1611 EAST U.S.A. Game sales and service only Atari, Inc.

New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ee From New Jersey (201) 469-5993 @ From anywhere else in this area ‘toll-free (800) 526-3849 EUROPE Parts for all Atari customers in Western Europe. Game sales and service Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) @ 06252155 TIPPERARY TOWN, IRELAND

Page 2

Battlezone Open-Face Conversion Kit TM-184 1st Printing_Page_2.png

This kit replaces the plastic housing on the front of the Battlezone™ game. The kit provides greater monitor visibility for prospective players. If all tools required for this kit are at hand, you can do the conversion in less than two hours. The contents of this kit are as follows: Part No.

Description A037559-01 A037630-01 A037664-01 A037664-02 Wood Housing Assembly Bottom Retainer (with game instructions) A037664-03 75-050 82-1822 82-1832 Xinvert Jumper Wire (AMP single-leaf terminals) #10 Internal-Tooth Zinc-Plated-Steel Lock Washer #8 x 1 3/8-inch Cross-Recessed Wood Screw #8 x 2-Inch Cross-Recessed Wood Screw 82-8016B 037568-01 037576-01 037577-01 #10-32 x 1-Inch Button-Head Hex-Socket Machine-Thread Monitor Sheif Top Retainer ~ Middle Retainer 037628-01 037629-01 037646-01 Attraction Panel Monitor Shield Cardboard Monitor Bezel X-Invert Jumper Wire X-Invert Jumper Wire (Molex terminals) (AMP twin-leaf terminals) \ Black Screw Preliminary Steps Unlock and open the rear access panel of the game.

(It is not necessary during this conversion procedure to open the contro! panel.) Remove the following parts from your Battlezone™ game: @ —_A— ~_—_ WARNING Housing assembly (see removal instructions on High , voltages may exist in any televi- page 21 of your Battlezone manual) sion or monitor, even with power discon- Black monitor bezel touch electrical parts of the yoke area with your hands or with metal objects in your hands! Mirror (see page 20 of the manual) Monitor assembly (see page 19 of the manual) “L-’shaped monitor support brackets Fluorescent light board assembly (see page 22 of the manual) nected. Use extreme caution and do not :

implosion Hazard If you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. placing any monitor. Tools required to convert the cabinet are: Hand saw Punch or power drill (for making pilot holies) Allen wrench set Phillips screwdriver Stapler (or small tacks and hammer) Glue (optional) “C”-clamps Use care when re-

Page 3

Battlezone Open-Face Conversion Kit TM-184 1st Printing_Page_2.png

BLACKLIGHT HARNESS REMOVE ALL DARK-COLORED ITEMS CUT OFF THIS EXTENSION BLACKLIGHT << ae BLACKLIGHT STARTER BALLAST Front View of Fluorescent Light Board Conversion Instructions Saw off the “tongue” or front extension on the fluorescent light board. The straightness of the cut is not critical: you can cut off + Remove and save the following parts from. the assemblies you took out of the game in Prelim- . % inch. Reinstall the fluorescent light board as de-.. scribed on page 22 of the game manual, and inary Steps: plug the harness connector back together. Fluorescent light board and cool white tube, with its associated ballast, transformer, clamps, starter, socket, and wires.

Holding the new monitor shelf in position at the rear opening of the game, align the shelf as Monitor and its associated mounting hard- ware (discard the wood mounting frame). Discard any of the remaining parts, unless you want to save some of them as spare parts for other games. Disassemble the monitor from the wood frame. Discard the wood frame, but save the four sets of mounting hardware. shown in the illustration. Use at least two “C”-clamps (with scrap wood for protecting the side-panel graphics), and hoid the shelf in position. Make four pilot holes in the plywood cabinet cleats. If possible, apply glue to the sides of the shelf.

Then install the shelf with the four 2-inch-long wood screws provided. This shelf becomes a permanent part of the cabinet. a

Page 4