cisco — Example: Configuring Layer 2 VNI with Spine Multicast Replication

Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter, x best-external, a additional-path, c RIB-compressed, t secondary path, L long-lived-stale, Origin codes: i - IGP, e - EGP, ? - incomplete RPKI validation codes: V valid, I invalid, N Not found Network Next Hop Metric LocPrf Weight Path Route Distinguisher: 172.16.254.3:101 * i [2][172.16.254.3:101][0][48][44D3CA286CC1][0][*]/20 172.16.254.3 0 100 0 ? *>i 172.16.254.3 0 100 0 ? * i [2][172.16.254.3:101][0][48][44D3CA286CC1][32][10.1.101.10]/24 172.16.254.3 0 100 0 ? *>i 172.16.254.3 0 100 0 ? Route Distinguisher:

172.16.254.4:101 * i [2][172.16.254.4:101][0][48][44D3CA286CC2][0][*]/20 172.16.254.4 0 100 0 ? *>i 172.16.254.4 0 100 0 ? * i [2][172.16.254.4:101][0][48][44D3CA286CC2][32][10.1.101.20]/24 172.16.254.4 0 100 0 ? *>i 172.16.254.4 0 100 0 ? Spine-01# The following example shows the output for the show ip msdp summary command on Spine Switch 1: Spine-01# show ip msdp summary MSDP Peer Status Summary Peer Address AS State Uptime/ Reset SA Peer Name Downtime Count Count 172.16.254.2 65001 Up 00:06:28 0 0 ? Spine-01# The following example shows the output for the show ip mroute command on Spine Switch 1: Spine-01# show ip mroute IP Multicast Routing Table Flags:

D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, G - Received BGP C-Mroute, g - Sent BGP C-Mroute, N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, Q - Received BGP S-A Route, q - Sent BGP S-A Route, V - RD & Vector, v - Vector, p - PIM Joins on route, x - VxLAN group, c - PFP-SA cache created entry, * - determined by Assert, # - iif-starg configured on rpf intf Outgoing interface flags:

H - Hardware switched, A - Assert winner, p - PIM Join Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 224.0.1.40), 00:56:14/00:02:21, RP 172.16.255.255, flags: SPL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (*, 225.0.0.101), 00:00:12/stopped, RP 172.16.255.255, flags: SP Configuring EVPN VXLAN Layer 2 Overlay Network Example: Configuring Layer 2 VNI with Spine Multicast Replication Configuring EVPN VXLAN Layer 2 Overlay Network 42