cisco — Example: Configuring Layer 2 VNI with Spine Multicast Replication

Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (172.16.254.4, 225.0.0.101), 00:00:05/00:02:54, flags: PA Incoming interface: GigabitEthernet1/0/3, RPF nbr 172.16.14.4 Outgoing interface list: Null (172.16.254.3, 225.0.0.101), 00:00:12/00:02:47, flags: PA Incoming interface: GigabitEthernet1/0/2, RPF nbr 172.16.13.3 Outgoing interface list: Null Spine-01# The following example shows the output for the show ip mfib command on Spine Switch 1: Spine-01# show ip mfib Entry Flags:

C - Directly Connected, S - Signal, IA - Inherit A flag, ET - Data Rate Exceeds Threshold, K - Keepalive DDE - Data Driven Event, HW - Hardware Installed ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client. I/O Item Flags: IC - Internal Copy, NP - Not platform switched, NS - Negate Signalling, SP - Signal Present, A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward, MA - MFIB Accept, A2 - Accept backup, RA2 - MRIB Accept backup, MA2 - MFIB Accept backup Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second Other counts:

Total/RPF failed/Other drops I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps Default (*,224.0.0.0/4) Flags: C HW SW Forwarding: 0/0/0/0, Other: 2/2/0 HW Forwarding: 0/0/0/0, Other: 0/0/0 (*,224.0.1.40) Flags: C HW SW Forwarding: 0/0/0/0, Other: 0/0/0 HW Forwarding: 0/0/0/0, Other: 0/0/0 Tunnel1 Flags: A GigabitEthernet1/0/3 Flags: IC (*,225.0.0.101) Flags: C HW SW Forwarding: 0/0/0/0, Other: 1/0/1 HW Forwarding: 0/0/0/0, Other: 0/0/0 Tunnel1 Flags: A (172.16.254.3,225.0.0.101) Flags: HW SW Forwarding: 0/0/0/0, Other: 0/0/0 HW Forwarding: 0/0/0/0, Other: 0/0/0 Tunnel1 Flags: A GigabitEthernet1/0/2 Flags: NS (172.16.254.4,225.0.0.101) Flags: HW SW Forwarding:

0/0/0/0, Other: 0/0/0 HW Forwarding: 0/0/0/0, Other: 0/0/0 Tunnel1 Flags: A GigabitEthernet1/0/3 Flags: NS Spine-01# Return to Verifying the Layer 2 VNI with Spine Multicast Replication, on page 33 . Configuring EVPN VXLAN Layer 2 Overlay Network Example: Configuring Layer 2 VNI with Spine Multicast Replication Configuring EVPN VXLAN Layer 2 Overlay Network 43