DOP-EXIO_instruction sheet (EN)

1. Please use the 28-16 AWG (1.5mm 2 ) single-core bare wire (Solid type) or the multi-core wire (Stranded type) for the I/O wiring. The stripped length of the wire should be 6-7mm, and the torque specification of the screw for the terminal is 4.5lb-in. Please refer to the specifications of the terminal shown 2. DO NOT install the Extension Digital I/O Module in a location high temperature and high humidity (where 2. Allow a minimum space of 50mm between the Extension Digital I/O Module and other control devices, and 2. DO NOT place the I/O signal wires and power supply wire in the same 1.

DO NOT install the Extension Digital I/O Module in a place subjected to corrosive or flammable gases, 3. DO NOT install the Extension Digital I/O Module in a location where vibration and shock will exceed 1. Please avoid any conductive debris and tiny metal material enter the Extension Digital I/O Module when Sink = (common port for current input S/S) Source = (common port for current output S/S) keep the Extension Digital I/O Module away from the high-voltage lines or any power equipment. ™ There are two types of DC inputs, SINK and SOURCE, and they are defined as follows: X0 in the figure on the left. temperature and humidity will exceed specification). wiring duct.

liquids, or airborne dust or metallic particles. [ Installation & Wiring 22-16AWG screwing and wiring. 4.3 Input Point Wiring S/S Sinking specification. 4.1 Wiring available only with I/O of the MPU mal H 16bit: 0000 ~ FFFF 32bit: 00000000 ~ FFFFFFFF Self Diagnosis / Protection I/O check, system execution timeout check, invalid command check, program check and password settings Batch I/O (refresh) Immediate refresh command Basic command (30 us) Application command (30 ~ hundreds us) Commands + Ladder Diagram + SFC Step commands included STL commands) Application commands:

59 1280 Points M0 ~ M511 + M768 ~ M999 + 64 Points T0~T63 (100 ms time base) 63 Points T64~T126 (10 ms time base) 13 Points C235 ~ C254 (all of them are 5Hz 9Hz Item Specifications Remark 999 Steps Built-in EEPROM 1 Points T127 (1 ms time base) 16bit: -32768 ~ +32767 32bit: -2147483648 ~ 128 Points S10 ~ S127 M1000 ~ M1279 256 Points M512 ~ M767 112 Points C0 ~ C111 16 Points C112 ~ C127 latched type) 408 Points D0 ~ D407 192 Points D408 ~ D599 +2147483647 Constant Hexadeci Monitor / Debug Program execution time display, bit / word, device settings 64 Points P0 ~ P63 2 E, F Response Time Approx. 10 ms Stored program, cyclic scan system - Basic commands:

32 (including the Y Function Specifications http://www.delta.com.tw/industrialautomation/ 3 DOP series Extension Digital I/O Module should be used with DOP-AE series HMI product. Ensure to switch off the power before wiring. 3 Please install this DOP series Extension Digital I/O Module in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required for opening the enclosure) in case danger and damage on the device may occur. 3 DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur.

Check all the wiring again before switching on the power. 3 DO NOT place any heavy objects on the connection port of DOP series Extension Digital I/O Module. Doing so may damage the product. Extension Digital I/O Module 3 DO NOT touch any internal circuit in 1 minute after the power is switched off. Do NOT touch any terminal when the power is switched on. 3 Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference. Input Unit Output Unit Model Name Power Point Type Point Type DOP-EXIO14RAE 8 6 Relay DC Type Sink or Source 12 Relay 1.1 Model Explanation DOP - EXIO 14 R AE (1) (2) (3) (4) (5) 3 4 (3) Input / Output Point 14:

8 input points / 6 output points 28: 16 input points / 12 output points Instruction Sheet (1) Product Name DOP: Delta Operation Panel (2) Series EXIO: Extension Digital I/O Input / Output (5) Applicable HMI Series AE: DOP-AE Series HMI (4) Output Contact Type R: Relay 3. Input / Output Terminals 4. Nameplate 3 Please read this instruction carefully before use. 1. Connection Port 2.

Direct Mounting Hole 5VDC, supplied by HMI 16 DOP-EXIO28RAE X Introduction Warning 1.2 Product Outline 1 2 1.3 Model Name Item Specifications Remark Control Method Stored program, cyclic scan system - Immediate refresh command I/O Processing Method Batch I/O (refresh) available only with I/O of the MPU Execution Speed Basic command (30 us) Application command (30 ~ hundreds us) Program Language Commands + Ladder Diagram + SFC Step commands included Program Capacity 999 Steps Built-in EEPROM Basic commands: 32 (including the Commands Application commands:

59 STL commands) Step Relay (Latched) General Step Point 128 Points S10 ~ S127 M0 ~ M511 + M768 ~ M999 + General 1280 Points Auxiliary M1000 ~ M1279 Relay Latched 256 Points M512 ~ M767 Timer Digital 64 Points T0~T63 (100 ms time base) 63 Points T64~T126 (10 ms time base) 1 Points T127 (1 ms time base) General 112 Points C0 ~ C111 Latched 16 Points C112 ~ C127 Counter C235 ~ C254 (all of them are 32bit 13 Points latched type) Data Register General 408 Points D0 ~ D407 Latched 192 Points D408 ~ D599 Pointer P 64 Points P0 ~ P63 Index Register E / F 2 E, F 32bit: -2147483648 ~ Decimal K 16bit: -32768 ~ +32767 +2147483647 Constant Hexadeci 16bit: 0000 ~ FFFF 32bit:

00000000 ~ FFFFFFFF mal H Self Diagnosis / Protection I/O check, system execution timeout check, invalid command check, program check and password settings Monitor / Debug Program execution time display, bit / word, device settings (1) Product Name DOP: Delta Operation Panel (2) Series EXIO: Extension Digital I/O 14: 8 input points / 6 output points (3) Input / Output Point 28: 16 input points / 12 output points (4) Output Contact Type R: Relay (5) Applicable HMI Series AE: DOP-AE Series HMI S/S Sinking X0 X0 S/S Sourcing Item / Model Name DOP-EXIO14RAE DOP-EXIO28RAE Power Supply Voltage Power Consumption 5VDC, 1A (supplied by HMI) 0.25W 0.5W Noise Immunity RS: Frequency:

80MHz ~ 1GHz, 1.4GHz ~ 2.0GHz, Test level 10V/m CS: Frequency: 0.15MHz ~ 80MHz, Test level 10V (HMI power port & I/O line) ESD: Air discharge ±8KV EFT: ±1.5KV (HMI power port) ±1KV (I/O line) Ambient Temperature / Humidity Surge: ±2KV (HMI power port) Operation: 0°C ~ 50°C (Temperature), 10 ~ 90% (Humidity), Storage: -40°C ~ 85°C (Temperature), 10 ~ 90% (Humidity) Vibration / Shock IEC 61131-2 Compliant 5Hz≦f＜9Hz = Continuous: 1.75mm / Occasional: 3.5mm 9Hz≦f≦150Hz = Continuous: 0.5g / Occasional:

1.0g X, Y, Z directions for 10 times DC Signal IN Input point loop equivalent circuit Wiring loop SINK mode +24V 24VDC 0V SINK +5V S/S X0 +24V OV S/S X0 X1 X2 24VDC Sink Type DC Signal IN Input point loop equivalent circuit Wiring loop SOURCE mode +24V 24VDC 0V SOURCE +5V S/S X0 +24V 0V S/S X0 X1 X2 24VDC Source Type Input Point Electric Specifications Input Type Input Voltage DC (SINK or SOURCE) 24VDC (5mA) Active Level Off→On, above 16VDC On→Off, below 14.4VDC Response Time Approx.

Стр. 1