US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com resilient circular pad (gas check pad) mounted between the flat front faee of the plug and the head of a mushroom-shaped obturator spindle whose stem extends rearward, slidably supported in an axial bore in the plug. Propellant gas pres- sure forces the head of the spindle rearward, com- pressing the pad against the nose of the plug and thereby forcing the pad to expand radially against the inner surface of the tube. The peripheral sealing surface of the pad is protected at the front and rear edges by steel expanding rings. Figur* S-8.

Plug-type Cannon Breech Closure Stepped Thread, Horizontal Swing 3-5.2.2.1.2 Locking Arrangement support or housing of the closure and other parts of the breech mechanism. The term breech ring is commonly used in reference to nonautomatic cannon, while.receiver applies to the corresponding part in automatic cannon, in machine guns, and in most types of small arms. The member usually serves also as a principal or supplementary support of the tube or barrel in its mount or stock, and in some cases reinforces the tube wall about the cham- ber against internal radial pressure.

The common feature of all types is a bore or socket to receive the tube; otherwise the shape varies widely, in accordance with the purposes served and the design of the mechanism supported.. To obtain sufficient strength in the breechblock threads to withstand propellant pressure, to avoid excessive size and weight of the breechblock, and to minimize the motion required to seat the block, an interrupted, or sectored, thread is employed. That is, the exterior of the breechblock and the interior of the breech (breech- recess) are formed with equal numbers of threaded arcs alternating with longitudinal clearance channels.

Alignment of the threaded arcs of the breechblock with the clearance channels in the recess permits insertion or with- drawal of the breechblock by simple forward or rearward movement and locking or unlocking by rotation through a fraction of one turn to engage or disengage the threaded areas. Loss of strength incurred by lack of threads in the clearance chan- nels is compensated by increased length or in- creased diameter of the threaded area of the breech- block. In the Bof ore breechblock increased threaded area has been obtained by making the breechblock markedly larger at the rear and giving it a conical or ogival taper forward.

This construction pre- sents an advantage in reduction of the straight line retraction needed before the breechblock can be swung out of the recess on a pivoted carrier. How- ever, recent practice favors the Welin or stepped- thread type of construction (Figure 3-8), in which the radii of breechblock and recess cross sections are increased in a series of steps in successive sec- tore, each series being repeated an equal number of times in the circumference of both members.

In each series, all breechblock sectors are threaded except the one of smallest radius, which is small enough to clear the smallest radius sector of the recess; and all recess sectors are threaded except the one of largest radius, which is large enough to clear the largest radius sector of the breechblock. Mobile closures may be classified into types as (a) plug, (b) bolt, (c) sliding breechblock, and (d) eccentric screw. 3-5.2.2.1 Plug-type Breechblock Closures (see Figure 3-8) This type is often called the interrupted screw or the slotted strew type- Closures incorporating plug-type breechblocks are applied to cannon em- ploying separate loading ammunition.

In this type an opening (breech recess) is formed in the tube at the rear of the chamber, or partly in the tube and partly in the breech ring, for ammunition insertion. The opening is closed by a closely fitting plug, which is carried axially (or nearly so) to a nearly seated position, then rotated to complete the closure. The rotation engages mating inter- rupted threads on the plug and within the recess to seat the plug and retain it in position against the pressure developed by the propellant. 3-5.2.2.1.1 Obturation Gas leakage past the plug is prevented, in current designs, by an obturator, consisting of a