US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com ihe crank arm and connecting rod are nearly Aligned, so that rearward pressure on the bolt pro- duces a very small rotational component of force at the crank pin and initial rearward movement of the bolt is impeded. chamber as the block moves to closed position, and the front edge of the leading end of the block (when closing) is beveled to push forward an incompletely inserted cartridge. This end of the block is also cylindrically grooved from front to rear to provide a guiding trough for the entering cartridge. A central bore in the block houses the firing pin (usually percussion type) and its immediate con- trolling mechanism.

The artillery primer, as this type primer is called, is permanently inserted into the cartridge case at the loading plant and requires no separate action for insertion or removal at the gun. (b) Rolling-contact-type. This is a modification of the crank-type, in which the end of the crank arm and the crank end of the connecting rod are rounded abutting surfaces held in contact by an additional link. The effect of this modification is to retard the increase of the rotational component of force on the crank arm during the initial stage of rotation, and so to produce a greater delay than the simple crank device. (c) Inclined-contact- or wedge-type.

In closed position, the bolt and receiver (or barrel) are con- nected by mating interrupted threads, or by a transverse sliding bar, with the engaged surfaces inclined at such an angle that a positive lock is not obtained. When the propellant pressure acts on the bolt, rearward movement is impeded until the small component of force parallel to the inclined surfaces rotates or slides the opposing members out of engagement. Extractor levers pivoted or fulcrum-mounted in the breech ring recess are actuated through their integral follower lugs, which bear slidably in in- clined camming grooves in the breechblock.

Where closing is accomplished by spring action, the ex- tractor lugs engage offset seats at the ends of the cam grooves to lock the breechblock in open posi- tion. Unlocking is then accomplished by insertion of the next cartridge, its rim striking the extractors to unseat the follower lugs and restore them to the camming groove. Motion of the breechblock is cus- tomarily effected by partial rotation of an operating shaft carrying the breechblock crank whose crank pin slides in an inclined slot on the breechblock to slide it in opening and closing travel.

This term, through custom, applies to those de- signs in which opening and closing of the breech is accomplished principally by movement of a block in a direction normal to the axis of the chamber; i.e., across the face of the opening. Sliding breech- block types in service to the present provide no gas seal, obturation being effected by use of a car- tridge case. Movement of the breechblock is guided by suitable slide surfaces in the supporting breech ring or receiver. Generally the bearing surfaces are inclined slightly to obtain a wedging action to ensure full seating of the cartridge, hence, this type of closure is often called sliding wedge.

3-5.2.2.3 Sliding Breechblock Closures 3-5.2.2.3.2 Small Arms Applications Applications of the transversely sliding breech- block principle in present Army small arms are limited to revolver-type mechanisms. Former ap- plications, U. S. and other, military and commer- cial, include the following: (a) Drop Block A closure in which the breechblock slides upward to close, downward to open, guided by grooves in opposite sides of the receiver and actuated by suit- able linkage connecting to an operating lever be- neath the receiver. The lever handle is shaped to form a trigger guard.

Typically, a spring-loaded pivoted hammer is released by the trigger to strike a firing pin carried in the breechblock. 3-5.2.2.3.1 Cannon Applications (see Figure 3-14) In cannon, the typical sliding closure consists of a block (wedge) of roughly rectangular outline, which slides in a corresponding recess through the rear portion of the breech ring. The motion may be horizontal or vertical; however, the vertical, or drop block, arrangement is currently more gen- erally used.

Mating ribs and grooves on the block and within the brooch ring recess are inclined slightly to wedge the cartridge forward into the (b) Rolling Block The block swings rearward and downward about a transverse pivot below the chamber to open the breech. 3—12