US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com y 4-2.2 -Shape of Chamber conform to that of a manufacturable case, and be tapered as required to facilitate extraction of the case after firing. Optimum chamber contours are established through appropriate consideration of the effects of chamber shape on propellant performance and on (fun structure, and of the details of contour best suited to the type of round to be used and to the manner of operation of the gun mechanism. Where various factors exert opposing influences, a com- promise is determined in accordance with the rela- tive importance attached to the opposing factors in the specific gun being designed.

The determination of length-to-diameter ratio of chambers for cartridge cases should include due consideration of the effect of the case proportions on practicability of case manufacture, suitability of ammunition units for storage and transportation, and ease of handling the rounds in firing opera- tions. (2) In guns using separate loading ammunition, the main cavity is commonly cylindrical, with a slight flare near the rear end to provide a conical seat for the obturating parts on the nose of the breechblock.

If the diameter of the chamber sub- stantially exceeds that of the projectile, the rear portion of the chamber may be conically reduced to near projectile diameter to permit use of a smaller obturator and breechblock. Such a conical reduction of the chamber is designated as the cham- ber rear slope (see Fig» 3-1 (B)), and the resulting restriction of diameter is termed a choke. 4-2.2.1 Effect on Propellant Performance Round-to-round uniformity of propellant action requires uniformity of propellant ignition, com- bustion, and resultant pressure generation.

The requisite rapid and complete ignition of all por- tions of the propellant is promoted by a compact shape of chamber, which shortens the necessary travel of the igniting flame from its origin to the remotest portions of the propellant. While breech loading requires that the chamber diameter exceed the bore diameter sufficiently to permit insertion of the projectile, comparative firing tests indicate that projectile velocity is in- creased somewhat by making the chamber diameter substantially larger than the bore. Ratios in use rдnge up to roughly 1.5 to 1. The considerations favoring large chamber diameter must be recon- ciled with opposing factors indicated below.

(3) In recoilless guns, the required shape of chamber may be such as to fit the cartridge closely throughout, or to fit only at specified zones, the requirement being dictated by the design of the case and the intended path of gases to the breech nozzle or nozzles. While current designs are based on a maximum propellant pressure substantially lower than that employed in closed-breech guns, the chamber retains its function as a pressure-contain- ing vessel, and is subject to essentially the same mechanical design considerations as are closed breech chambers. Hence, the chamber is basically cylindrical or moderately taperцd.

The ratio of diameter to length, degree of taper, and details of contour of front and rear ends are subject to the requirements established by the interior bal- listics designed to obtain the desired projectile acceleration, accompanied by balanced forward and rearward impulse on the gun. 4-2.2.2 Effect on Gun Structure For safe containment of a given pressure, the larger the chamber cross section, the greater the required wall thickness in the breech end of the tube or barrel and in the breech closure. The resultant greater weight in the breech closure also necessitates the use of greater force in opening and closing the breech.

Influence of these factors tends to limit the maximum diameter of the chamber. Opposing this consideration, in some cannon de- signs, is the desirability of limiting the length of gun structure behind the supporting trunnions, to minimize the clearance required for loading and firing at high angles of elevation, or to reduce the required size of an enclosing turret. 4-3 Bore Characteristics The basic bore functions of guiding the initial movement of the projectile and providing expan- sion space for the propellant to perform its work of acceleration indicate that the bore should, in all cases, embody the closest practical approach to providing:

(1) at any cross section, a balanced distribution of cross sectional area about a straight 4.2.2.3 Effect on Other Features of Design (1) In guns using cartridge cases (excepting some recoilless weapons), the chamber shape must