US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com longitudinal axis; and (2) a continuity and smooth- ness of bore surface to enable maintenance of an effective seal against escape of propellant gas around the projectile before the latter emerges from the muzzle. Other bore characteristics, sub- ject to variation in accordance with the intended use of the weapon/are (a) caliber, (b) bore length, and (c) bore surface detail. (scatter) of the pellets after they have left the bore (see also par. 3-4.2).

4-3.2 Bore Length The length of the bore, from chamber to muzzle, combines with the bore diameter and chamber vol- ume to determine the ratio of expansion (final volume/initial volume) of the propellant gases during their action of propelling the projectile through the bore. All these factors, as well as orojectile weight and the amount and rate of pres- sure production by the propellant charge, must be considered in various combinations to obtain the proportions for a new design of gun to meet most satisfactorily the specified performance, dimen- sional and weight requirements. The term caliber denotes the diameter of the bore, exclusive of rifling grooves if such are present.

(It is also used to indicate the nominal diameter of the projectile.) In former U. S. Army design practice, caliber was usually expressed in inches and decimal fractions thereof; in recent practice, the measurement is expressed in millimeters and decimal fractions thereof. (The significance of caliber as the bore diameter dimension should not be confused with the practice of indicating the length of bore or gun in calibers, for example, a "6 inch 50 caliber gun" indicates a caliber of 6 inches and a length of 6 X 50 = 300 inches.) 4-3.1 Caliber 4-3.3 Bore Surface Detail Bores are generally designated in accordance with surface characteristics as follows: (1) Smooth Bore.

This designation indicates that the bore is circular in cross section, without any pattern of grooves or ridges designed to pro- duce rotation of the projectile. Its chief military use at present is in muzzle-loading mortars (see also par. 3-4.3.1). The caliber, as a determinant of the sectional area of the projectile exposed to propellant pres- sure, is a major factor in projectile acceleration, and in the rate of change of propellant gas volume as the projectile moves through the bore. (2) Rifled Bore.

This designation indicates that the bore contains multiple, parallel grooves following helical paths about the bore axis, de- signed to engage the periphery of the projectile (or a band fixed thereon) and so impart a desired rotational velocity to the projectile as it is propelled through the bore (see Fig. 3-7). The rotation serves to maintain the axis of the projectile closely coincident with the direction of projectile travel, to reduce the amount and variations of air resist- ance, and to insure a nose-first impact on the target. Caliber may be characterized as follows: (1) Constant Caliber (Cylindrical Bore).

Con- stant, or uniform, caliber denotes a bore having the same caliber throughout its length. This is the prevailing type in current military gun design (see also par. 3-4.1). (2) Decreasing Caliber (Tapered Bore). In some experimental designs, bores having a larger caliber at the rear than at the front have been used for attainment of high velocity. In such designs a deformable ring or skirt is used on the projectile to seal against propellant gas loss, and this is com- pressed or collapsed to smaller diameter as it moves through the bore. The reduction in bore size may be continuous through the bore length or confined to some forward portion of the length.

The larger area subjected to gas pressure in the zones where pressure is at or near peak pressure effects an in- crease in acceleration of the projectile. A slight reduction in caliber (choke) near the muzzle of some shotguns is used to reduce the lateral spread The number of and cross section of rifling grooves must be made sufficient to provide the bear- ing area necessary to impart the required projectile rotation without excessive stress in the materials of the bore and projectile, in order to avoid rapid wear and the possibility of stripping (shearing) the lands (ridges) of either projectile or bore.

The needed number and size of grooves increases with increases in the weight of projectile and in the ro- tational acceleration necessary to attain the rota»- tional velocity required for stability. Designs in current U. S. Army use show the number of grooves