US Army Materiel Command AMCP 706-250 — Engineering Design Handbook: Guns Series — Guns-General

Downloaded from https://www.everyspec.com material; by limiting the generated pressures and temperatures to the extent that size, weight, and ^ performance requirements will permit; and by use W of such means as are practicable for minimizing the heat absorbed by the interior surfaces of the tube and for increasing the rate at which the ab- sorbed heat can be removed from the critical inner layers. thickness by small arms procedure is greater than that used in cannon procedure. The weight and center of gravity of a gun must be considered in connection with the manner of transport and use.

In shoulder- or hand-supported guns, weight and its location are prime factors in governing the amount of energy to be absorbeckby the firer, and the amount and direction of deflection of the gun from the line of sight on firing. Other factors being equal, velocity of recoil and amount of "jump" decrease with increasing weight and closer alignment of bore axis, center of gravity and center of support. However, greater weight de- creases ease of carrying and handling, and some degree of nonalignment of bore and support sim- plifies practical solution of the sighting problem. The most advantageous compromise between op- posing considerations should be sought in each case.

6-2.5 Weight 6-2.4 Firing Rate In the brief period of burning of the propellant and ejection of the projectile, the high temperature of the gases causes the transmission of heat into the metal at the bore surface more rapidly than it can be transmitted into the intermediate and outer metal of the tube. The metal at the inner surface is consequently heated to a temperature so high that minute particles of softened metal may be eroded and blown out of the bore by the propellant.

If firing is repeated before the surface metal has cooled sufficiently to regain normal strength and wear resistance, the weakened metal will be subject to wear by the second projectile, plus firing stresses, and to an additional. increase in temperature. Repetition of the cycle at short intervals can result in rapid deterioration of the bore surfaces. The rate of fire is thus an important determinant of the service life of a gun, and a rapid rate should be planned only with due regard for the penalty in reduction of number of effective rounds that may be fired before the tube requires replacement.

Where rapid fire is an accepted requirement, the methods of combatting erosion indicated in para- graph 6-2.3 should be carefully considered. Similarly, in cannon and other mounted guns, stability in firing is favorably affected by increased weight and by reduction of moment arms between bore axes, centers of gravity, and supporting and recoil-resisting forces. However, where mobility is a desired characteristic, minimum practical weight of the complete weapon is desirable, and the designs of the gun and mount or carriage should be coordinated to obtain the optimum over- all solution for the intended use.

When the mount or carriage includes a recoil mechanism (to reduce the firing forces applied to ground or supporting structure), the weight and location of center of gravity affect: (a) the length of recoil and resist- ing forces required; (b) the energy needed for counterrecoil movement of the recoiling parts; and (c) the supporting forces necessary for stability throughout the recoil and counterrecoil movements at all contemplated angles of gun elevation.

Since the weight characteristics are essential factors in design of the carriage or mount, the carriage de- signer is submitted a tentative design of gun tube and parts carried thereon, with pertinent weight data, for coordination prior to completion of de- tails.

In formulating the tentative design, con- siderations of weight and its distribution will normally yield precedence to those of strength, performance, operation, etc.; within the latitude permitted.by other factors, the center of gravity should generally lie on or near the axis of the bore Since the effectiveness of small caliber weapons may depend on the firing of a large number of projectiles in a short time, and since relatively small, light projectiles are more readily handled either manually or by rapid automatic mechanisms, the rate of fire is a matter of greater concern in small arms and small caliber automatic cannon than in the larger caliber weapons.

Moreover, in the relatively thin-walled barrels of small bore guns, there is less heat-absorbing metal per unit of bore surface, so a given thickness of excessively heated metal about the bore effects a greater pro- portionate loss in stress capacity of the small-bore type of barrel than in those of larger caliber. Prom these considerations, among others, the allowance for thermal effects included in determining barrel