Downloaded from https://www.everyspec.com through the bore, to accelerate it to the required muzzle velocity. Calculated curves of propellant pressure (ordinates) versus projectile travel in the bore (abcissa) are constructed for tentative com- binations, and these provide useful means of selec- tion of the optimum combination. The area under the curve, from beginning of travel through the length of bore, represents the work done in accel- erating the projectile; while the ordinates provide bases for strength requirements at all sections of the tube and for pressure-resisting parts of the breech closure (see Pig. 5-1).
effects on accuracy, a wide angle between the pro- jectile axis and the line of travel may cause failure of such artillery projectiles as depend, for effective- ness, on detonation by nose impact or on penetra- tion of armor or other structural material. To reduce the spin necessary for stability in the earlier portion of the trajectory, the projectile should be discharged from the gun with as little yaw as prac- ticable. To this end, the projectile and bore designs should be so coordinated that:
on insertion of the projectile into the rear of the bore, the longitudinal axis is aligned as accurately as possible with the centerline of the bore; sealing of the propellant gases is maintained as the projectile moves through the bore; and contours of the rear of the projectile and gun muzzle (including attachments) are not such as to cause unbalanced gas blast pressures on the rear end of the projectile on emergence from the bore.
6-2.2 Accuracy While the external air forces affecting accuracy of projectile night to the target cannot be com- pletely neutralized by forces applied to the pro- jectile by the gun, certain features or details of gun design may be employed to reduce or control in some measure the effects of unbalanced air forces. 6-2.2.2 Whip 6-2.2.1 Yaw Some cannon designed with relatively thin-walled tubes composed of relatively high strength steels have shown marked .elastic deflection normal to the longitudinal axis (whip) on firing. Insufficient study has been made to determine what relation exists between tube rigidity and firing accuracy.
Pending accumulation of experimental data suffi- cient to isolate the influence of whip from other sources of inaccuracy, the effect of whip cannot be rationally evaluated. If a minimum of variability of flight is to be achieved with a projectile having a length exceed- ing its diameter, yaw must be minimized. That is, at all times during flight, the longitudinal axis of the projectile must be as nearly coincident as pos- sible with the line of flight, so that, in still air, air resistance forces will be distributed as evenly as possible about the circumference of the projectile.
However, even assuming perfect launching, air movement (wind) would effect an unbalance, tend- ing to deflect the projectile from its theoretical path. If the resultant of the unbalanced air forces is ahead of the center of gravity of the projectile, the turning movement may not only increase the yaw, but tend to induce tumbling. To combat these tendencies, the projectile may be provided with fins at the rear to produce a correcting air force moment; or the stability of the projectile may be improved by imparting a spin about the longitu- dinal axis by means of rifling in the bore of the gun.
6-2.3 Erosion The useful life of a gun depends largely on the ability of the chamber and bore surfaces to resist erosion and abrasion by the hot propellant gases, projectile, and unburned particles of propellant. The deterioration of these surfaces reduces the velocity and accuracy by increasing the effective chamber size, shortening the bore, increasing leak- age of gases past the projectile, destruction of rifling, and increasing clearances to aggravate tendencies toward balloting and initial yaw.
A short gun life obviously increases the cost of an adequate supply of replacement weapons, including all logistic problems of storage, transportation, dis- tribution, and quick availability in emergency. If the rifling method of stabilization is used, un- necessarily rapid spin is to be avoided, as excessive stability will cause the axis of the projectile to persist in upward inclination as the trajectory curves downward, thus effecting excessive yaw in the latter portion of the trajectory. Aside from Early failure by erosion may be combatted by: use of heat abrasion resistant material for the parts involved, or use of a liner or plating of such