— AMCP 706-286 — Engineering Design Handbook (1963)

Downloaded from https://www.everyspec.com ~. I pre-:?nce of creep to that caused by p~urely 1 STE~ANALYSIS elastice (linear) deformations depends only on the value of n:V R. 2n + 1 (38 a iew typical values fol~ow: n 1 3 7 91L 1 0.78073;0.(1714 0.704~ 0.6I I 3-9.4. Failur2-, A tensile speckmen s:ub- jected to a con.-tant load fails by necking/ down and fracturing through the smallest C35section. Wrhen the material is metal- lographicaily s~tble and when its creep de-J formations follow the law of Bquaticn 1/ (3-58), the critical time, that is the time elapsed between load application and frac- ture, can be given a,,-:Fgr - .DsetdClm t,, = I ne. (13 69) .

fte}trln o h ounfo, h wherv i., is the creep rate at the moment of~ o h etrl'e fteclm ri h load application line of load application. The small leve' i,,= ksv Xy,' (0, 70) arms y., upon which the load "' is atn ~ with k,, the -- xerimentaiy determined con- equally be cau.,ed by inaccuracies in the man- ) stant at th~e proe epeaue ufacture (if the column and in its centering k,= k, e 111.T (37~ in the loading machine. Ur',er these bending When ~ ~ ~ ~ ~~ G t71aera smealgapia moments the small initial curvatire of the W entemierial las m~~e tyrpial Column increases in conse~quence c.J bending untale ', =; =const. (3 72) creep. The increased curvature, in turn, are fte deive frm exerient,.

uch leads to increased bending momtnts because are ftenderved romexpeimets. uch of the increases in the lever arm , y. As creep recent information on creep rupture can be in metals is non-linear, the Jncre.sps in curv- found in R~eference 24. atr n elcintk lc eysol With a machine or .r,?hanisnr which binds tit the beginning, but they are accelerated in and becomes inoperative if a maximum per- atraildeecinak aevrysoy the later phases, of the creep column testI missible dleformation is exceeded, the analyst unercsttlod 4; must calculate the time at which the corres-. pondng ree stainis eaced.An pprxi- Probably the mo. ;nteresting fact about poningcrep tran i rechd.

n aproi- the buckling of a cojumn in the presence mate evaluation of this time is facilitated by ofcepithtwlehecum istae isochronous stress-strain curves; they are a i t nta lgtycre tti e family of curves in the stress-strain plane coeustbew nthcrppoesi- with t = const. as the parameter. The creep creaes intbl curvature ufciety.oThis in- behvio atdiferet empratrescanbe be shown with the aid of the stress- } j ~correlated by means of parameters discussed ri dagmofte aeraesblhd int theeece2 temperature oftecolumn test 3-8,5. Creep Buckling. ,When a column Figure (3 '2)..

4'(see Figure 3-11) is subjected to two equal At the -- omen, of load applicaldon the &and opposite compressive loads, P, small besid- deviation is so small that virtually the ing moments M z Py, arise in its cross se, same stres.s (;,, prevails throughout the cross ( tions because of tL~e unavoidable deviation, section. But as the curvature increases iii li